The strength of the longitudinal joint is 50 kips/ft, whereas for the girth joint it is 25 kips/ft. Calculate the maximum diameter of the cylindrical tank if the internal pressure is 150 psi

Q: What is the value of Mn?

A: The values and figure given in the question are as follows: Side of square column(B)=500 mm Steel…

Q: Determine the axial deformation cylinder terms of R1, E1, R2, E2, P and L only.

A: Radius of inner cylinder is R1  Area of inner cylinder is A1=π R12   Area of outer cylinder A2=π…

Q: A steel pipe of length L=3.5m, outside diameter d₂ = 0.8m and inside diameter d: 0.6m. The inside of…

A:

Q: A compression spring is made of music wire of 2mm diameter having a shear strength and shear modulus…

A: The change in value of the stiffness=?

Q: دلها ↓↓ P 7 B vwx What is the Reaction Force induced in the following system at point A, if? Wo = 7…

A: A beam is given we need to find out the reaction at A

Q: Based on this, which of the following is true ? O a) The S1 bar is the tow bar. O B) The $4 bar is…

A:

Q: The 39-kg crate is stationary when the force P is applied. Determine the resulting acceleration of…

A: Given data:

Q: The pipe has a mass of 770 kg and is being towed behind a truck. (Figure 1) Figure G 0.4 m If the…

A: Given,m=770 kgθ=30°μk=0.2

Q: Problem 2: The steel shaft below is part of a mechanical assembly. The shaft is rotating at 125…

A: The rotation of the shaft at target rotation per minute results in the generation of power.  The…

Q: Determine the pressure difference (in kPa and answer should be a whole number) between the water…

A:

Q: A 13-m-long flat steel bar AB has a varying width as shown in the figure. Calculate the required…

A:

Q: 50 kN 30 kN- 3 m GH 30 kN- 3 m E 30 kN– 3 m

A:

Q: n coil diameter is 20 mm, nm and the number of e mean coil diameter is e stiffness of the spring is

A:

Q: Determine the steel area(s) required for the selections shown in the accompanying illustration. Do…

A: Given:  Fy =420N/mm2 F'c =28N/mm2 Es = 200 000N/mm2 Mu=750 KN.m b=350mm D=500mm   To Find: Area of…

Q: hydrostatic force

A: To find : ratio of the hydrostatic force exerted on the base and on any one of the vertical side

Q: A= 7420 mm d=252 mm bf = 203 mm tf = 13.5mm tw = 8mm 1x=87·10×106 mm²4 ly = 18.7*10% mm² →→PL 12x254…

A: Determine the fallowing: 1. Rmax 2. Euler's buckling stress 3. Critical buckling stress 4. Allowable…

Q: The pressure in tank is 2.99atm .Determine the gauge pressure.

A: Concept- Gauge pressure is defined as the difference of absolute pressure and atomospheric pressure

Q: RN, and a force, F= 66 KN) inclined at an angle alpha = 30 degrees from the vertical, such that it…

A:

Q: An aluminum tube of length 09.9(m) is used as column (fixed at both ends) carrying an axial load of…

A: Given: The length of the tube is 9.9 m. The axial load is 1319.67 N. The outer diameter of the tube…

Q: Calculate the wall thickness (t) of a 0.5 m diameter spherical tank, subjected to 40 MPa internal…

A: Given: Diameter, D = 0.5m Internal pressure, P =40MPa Allowable stress =120MPa Required: Wall…

Q: Question 2. Consider a hollow 7075-T6 aluminum alloy circular tube. Consider the inside diameter as…

A:

Q: Problem No. 7 A hollow shaft that has 100 mm outside diameter and 80 mm inside diameter is used to…

A:

Q: Question 2 A rectangular plane surface is 3 m wide and 6 m deep. It lies in vertical plane in water.…

A: first draw the figure then find the force

Q: 2 Y 25 500 mm 3 Y 25 30 mm = 500 N/mm2 All dimensions are in mm Doubly reinforced simply supported

A: Given data: fy=500 N/mm2d'=30 mm

Q: The system in the figure is supported by a column with a diameter of 50mm. If the modulus of…

A: Modulus of elasticity of the column is 70 GPa or 70000 MPa   Diameter = d = 50mm   L = 1m or 1000mm

Q: Q#1: The strength of the longitudinal joint is 25 kips/ft, whereas for the girth joint it is 20…

A: Longitudinal joint strength=25 kips/ft Girth joint strength=20 kips/ft Cylindrical tank internl…

Q: Determine the value of the critical load for the column, consider that the top end is adapted to an…

A: A column and a truss are given.The Young's modulus of elasticity, E = 70GPa   To determine the…

Q: - For the frame shown below, the initial displacement is 25 mm and the initial velocity is 13 mm/s.…

A:

Q: A compression spring is made of music wire of 2 mm diameter having a shear strength and shear…

A:

Q: Determine the AV (change in volume) of the 8-in. length of the rod shown if the rod is made of steel…

A: The basic relation between bulk modulus and young's modulus is          E = 3K1-2×μ29×106 =…

Q: The 62-mm-diameter solid shaft is made of 2014-T6 aluminum and is subjected to the distributed and…

A: Angle of twist = 0.0074 RadiansExplanation:Step 1: Step 2: Step 3: Step 4:

Q: 16. Fluid Flow through a Compression Chamber A compressible gas flows into and out of a compression…

A:

Q: The strength per meter of the longitudinal joint of a cylindrical tank is 475 kN, whereas the girth…

A:

Q: ering the effects of the prestressing forces (assume no loss) and the working lo e the selfweight of…

A: According to given data

Q: A homogeneous 62-kg block is suspended by three springs whose lower ends were originally at the same…

A: Given: For Steel spring, diameter of wire, d=12mm , number turns, n=22, mean dia= 120mm , G= 83MPa…

Q: Dont

A: Given data-    Inner radius(r) = 1.4 ft = 16.8 in Thickness(t) = 0.142 in Tensile stress (£) = 6968…

Q: 5) The rigid pipe is supported by a pin at C and steel guy wire AB 10 mm in diameter E = 200 GPa and…

A:

Q: In a 200 foot tall water tank, the pressure at the bottom is a. 1960 kPa b. c. d. 86 psi 25 psi 500…

A:

Pressure and Stress