The steel shaft is made from two segments: AC has a diameter of 0.5 in., and CB has a diameter of 1 in. The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft. G₁ = 10.8(10³) ksi. (Figure 1) Figure 0.5 in. C D 500 lb-ft 12 in. 1 in. B 1 of 1 > Part A Determine the maximum shear stress in the shaft Express your answer to three significant figures and include the appropriate units. μÅ Tmax=40.742 Submit ksi Provide Feedback Previous Answers Request Answer ? X Incorrect; Try Again; 3 attempts remaining

The steel shaft is made from two segments: AC has a diameter of 0.5 in., and CB has a diameter of 1 in. The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft. G₁ = 10.8(10³) ksi. (Figure 1) Figure 0.5 in. C D 500 lb-ft 12 in. 1 in. B 1 of 1 > Part A Determine the maximum shear stress in the shaft Express your answer to three significant figures and include the appropriate units. μÅ Tmax=40.742 Submit ksi Provide Feedback Previous Answers Request Answer ? X Incorrect; Try Again; 3 attempts remaining

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The A36 steel shafts as shown in the figure below are made from two segments: solid segment AC with diameter = 1 in and a hollow segment CB with an outside diameter = 2 in and inside diameter = 1 in. The shaft is fixed at both ends. Determine the magnitude of the applied torque T (lb-in) if the reaction at A is 600 lb-in clockwise.
A compound shaft consists of an aluminum tube (1) securely jointed to a steel tube (2). Both aluminum and steel tubes have an outside diameter of D= 48 mm and a wall thickness of t= 3 mm. The shaft is secured by a fixed support at one end and is subjected to a torque of T= 115 N.m at the other end. Determine the maximum stress in the shaft.[L1 = 200 mm, L2 = 350 mm, D = 48 mm , t = 3 mm, G = 75 GPa]
An aluminum shaft of two segments is shown below. Determine the allowable torque if the shear stress is not to exceed 30MPa and the angle of twist between the ends of the bar is not exceed 2.3°? (Assume G=80GPa)
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
The problem is stated below. However, change the position of torque to point C from point D. What is the effect of variation of torque placement in shaft CB?
The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid 1.86-in.-diameter steel [G=11400 ksi] shafts with lengths of L₁ = 79 in. and L₂ = 105 in., respectively. Assume Ng-27 teeth and N-42 teeth. The bearings shown permit free rotation of the shafts. (a) Determine the maximum shear stresses T₁, T2 produced in shafts (1) and (2). (b) Determine the rotation angle DA of gear D with respect to flange A. Answers: (a) T₁ = (b) P DIA Nc WWAMACOM Save for Later C 9.3808 = i 2.1378 e Textbook and Media NB L₁ B D TD ksi, 1₂: = i 14.5924 ksi. Attempts: 1 of 5 used Submit Answer
A compound shaft consists of an outside tube (1) and an inner tub (2) that are fully connected together. Determine the maximun allowable torque that could be applied to the compound shaft if the allowable shear stress in the outer shaft is Tall, 1 = 89 MPa, and the allowable shear stress in the inner shaft is Tall,2 = 62 MPa.[G₁: 39 GPa, G₂ = 16 GPa, d₁ = 102 mm, d₂ = 87 mm, d3 = 55 mm] Tube (1) Tube (2) Answer: d3 d₂ d₁ Tube (1) Tube (2) kN.m
Q1: The shaft BC is hollow with inner and outer diameters of 100 mm and 120 mm respectively. Shaft AB and CD are solid and of diameter d. For the loading shown determine the maximum and minimum shear stress in shaft BC. 0.9 m 0.7 m d 0.5 m A 120 mm T = 10 kN.m i В TB = = 20 KN.m 1 C D Tc = 30 KN.mi Tp = 6 kN - m Figure Question1