The steel bars AB and BC are pinned at each end and support the load 200 kN as shown in the figure. The material has a yield point of 200 MPa, and safety factor 2 for tension and 3.5 for compression. Use E = 200 GPa a. Determine the cross-sectional area of bar AB b. The horizontal displacement of point B 200 kN 30° 60° 2.00 m 3.46m

The steel bars AB and BC are pinned at each end and support the load 200 kN as shown in the figure. The material has a yield point of 200 MPa, and safety factor 2 for tension and 3.5 for compression. Use E = 200 GPa a. Determine the cross-sectional area of bar AB b. The horizontal displacement of point B 200 kN 30° 60° 2.00 m 3.46m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Question 6 A straight bar is fixed at edges A and B. Its elastic modulus is E and cross section is…

A: A straight bar fixed at edges A & B as shown- Elastic modulus = E, Cross-section area=A, Load…

Q: A 38-mm diameter by 3.5-m long steel rod (1) is stress free after being attached to rigid supports…

A: Given data in question Diamond 38 mmLength 3.5 mElasticity modulus 200 GPaCoefficient of thermal…

Q: The compound shaft in Figure is attached to rigid supports. For Bronze G = 40 GPa and for Aluminum G…

A: Given DataFor Bronze G=40 GPaFor Aluminium G=35 MpaDiameter of Bronze=200 mm=0.2 mDiameter of…

Q: Situation 11: The rigid bar ACE is supported by a pin at A and two horizontal aluminum rods, each of…

Q: 2. Consider a square bar 30 mm on side and 2.5 m long, having a material yield point 254 (in MPa).…

Q: Consider a square bar 30 mm on side and 2.5 m long, having a material yield point 254 (in MPa). An…

Q: If the output torque on the CD shaft is T ́ = 75 N-m and the motor rotates at 175 rpm, determine the…

A: Given for CD shaft diameter d2=35 mm, radius of gear R2=125 mmand torque T2=75 N-mfor EA shaft…

Q: A 12ft cantilever beam is subjected a 180 lb/ft uniform load and a vertical support of 1200 lb on…

Q: The rigid beam in (Figure 1) is supported by the three suspender bars. Bars AB and EF are made of…

A: Reference : Structural analysis, Stresses in bars. Given : Allowable stresses and area of bar. To…

Q: The bar AB is attached to aluminum and steel rods, horizontal before the load P is applied. Find the…

Q: Problem 5.9 A solid steel bar has a cross section of side b and is supported as shown. Knowing that…

A: To Determine Depth of the beam, b

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.8 in., b = 6 in., d = 4.0…

A: Given data:

Q: A = 2000 mm² A = 900 mm² B 503 mm 257 mm 355 mm The steel rod is stress-free before the axial loads…

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.6 in., b = 5.2 in., d = 4.1…

Q: A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal…

Q: Below is a truss created with 3 rod elements. Fixed at point A, sliding support at point C has. At…

A: Truss with 3 rod elements is: Cross section of rod: Elastic Modulus of rod E = 20 GPa Factor of…

Q: A 80 MPa 30° B 30 MPa 40 MPa

Q: Determine the vertical displacement of joint C. The length, L, of trusses AC, BC is 1,100 mm. The…

Q: a. Axial force on member ED from the real structure in kN. Put (-) negative sign if it's under…

A: Given Data: A truss of A=1200 mm2, E=200 Gpa α=12*106 /°C It is asked to find axial force in…

Q: Consider a square bar 30 mm on side and 2.5 m long, having a material yıeld point 254 (IH MPa). An…

Q: Three identical bars support a rigid beam that has negligible weight. Each of the three bars has a…

A: Objective: To determine the axial force in each bar. Given: Cross-sectional area of the bars (A) =…

Q: Bar AB is rigid and is attached to the steel and aluminum rods as shown in the figure. Before the…

Q: A stepped shaft of solid circular cross-section has length L 0.80 m, diameter d., = 40 mm and…

Q: A 26-mm diameter by 3.5-m long steel rod (1) is stress free after being attached to rigid supports…

Q: Determine the vertical displacement of joint C. The length, L, of trusses AC, BC is 1,000 mm. The…

Q: The bar AB is attached to aluminum and steel rods, horizontal before the load P is applied. Find the…

A: We will find force in Aluminium and use displacement formula.

Q: 2. The magnitude of the three forces acting on the plate are F₁ = 100KN, F₂=80kN and F3= 50kN. Solve…

Q: Determine the horizontal displacement of joint C. The length, L, of trusses AC, BC is 1,300 mm.…

A: EAC = 135 GPa = 135 × 103 N/mm2 EBC = 150 GPa = 150 × 103 N/mm2 AAC = ABC = 360 mm2 Determine the…

Q: Vertical rod CD of length L =2 m, cross-sectional area A = 150 mm2 %3D and modulus of elasticity E =…

Q: and a uniformly distributed load "w". The modulus of elasticity of the beam is 140GPa. Solve the…

Q: Four steel bars jointly support a mass of 25 x 103 kg. Initially the temperature is 250C. Bars A and…

Q: Four steel bars jointly support a mass of 25 x 10³ kg. Initially the temperature is 25°C. Bars A and…

A: Given, M = 25000 kg T1 = 25oC AA = AD = 480 mm2 AB = AC = 360 mm2 E = 200 GPa α = 11.7 x 10-6 /C

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.0 in., b = 5.3 in., d = 4.5…

A: Given: The value of a is 4 in. The value of b is 5.3 in. The value of d is 4.5 in. The value of t is…

Q: 2. An axial load of [A (100)] kiloNewtons is applied to a flat bar [B] mm thick, tapering in width…

A: Given, Axial load P = A(100) = 5(100) = 500KN Length (L) = 5m E = 200GPa = 200×10³mpa b1=120mm b2=…

Q: / The assembly consists of two 10-mm diameter steel rods AB and BC, and a rigid bar B. After…

Q: Determine: The shear diagram The moment diagram The value of the maximum bending moment The maximum…

A: Given: A simply supported overhang beam consisting of uniformly varying load and point load. To…

Q: Q1/ The assembly consists of two 10-mm diameter steel rods AB and BC, and a rigid bar B. After…

Q: y A 100 mm В 20 mm 150 mm 10 mm 20 mm 100 mm

Q: A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as…

Question

The steel bars AB and BC are pinned at
each end and support the load
200 kN as shown in the figure. The
material has a yield point of
200 MPa, and safety factor 2 for tension
and 3.5 for compression. Use
E = 200 GPa
a. Determine the cross-sectional area of
bar AB
b. The horizontal displacement of point
В
200 kN
30°
60°
2.00m
3.46m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Trending now

This is a popular solution!

Step by step

Solved in 7 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

i need the answer quickly
A uniformly-distributed load w is supported by a structure consisting of rigid bar BDF and three rods. Rods (1) and (2) are 16-mm- diameter stainless steel rods that have an elastic modulus of E= 185 GPa. Rod (3) is a 23-mm-diameter bronze rod that has an elastic modulus of E= 100 GPa. Use a = 1.4 m and L = 2.6 m. For a load magnitude of w = 30 kN/m, calculate (a) the normal stress in each rod. (b) the vertical deflection of the rigid bar at F. (1) B Answers: (a) 0₁ = i (b) VF = i a D 2 2a W E F MPa, 0₂ = mm IN i MPa, and 03 i MPa
A steel strip of length L = 200 mm is fixed at A and rest at B on a vertical spring of stiffness k = 2N/mm. The steel strip is 5 mm wide and 10 mm thick. A vertical load P = 50 N is applied at B as shown. Consider E = 200 GPa, the force (in N) developed in the spring is A L P B K
3
The couple M=1.1 kN-m acts in a vertical plane and is applied to a beam oriented as shown. Determine the stress at point A 10 mm 40 mm The stress at point A is ( 10 mm 40 mm -10 mm 1,-1.894 x 10 mm 1,-0.614 x 10 mm +0.800 x 10 mm MPa.
Mechanics of Deformable Bodies 6 in. in.- 5 in. 4 in. A steel tube with the cross section shown carries a torque T. The tube is 6ft and has a constant wall thickness of 3/8in. (a)Compute the torsional stiffness k=TTO of the tube. (b) If the tube is twisted through 0.5°, determine the shear stress in the wall of the tube. Use G=12x 106psi.
Problem # 4: Four steel bars jointly support a mass of 25 x 10³ kg. Initially the temperature is 25°C. Bars A and D have a cross-sectional area of 480 mm². For bars B and C, the cross-sectional area is 360 mm². Determine the elongation of bar A when the temperature becomes 60°C. Also, find the axial stress developed in bar C. Use E = 200 GPa and a = 11.7 x 10-6 m/ (m°C). 800 mm D 20 B °8 25000 kg 20 O
A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. Neglect deflections of the bar due to bending. Use E-200 GPa. How much will rod CD elongate due to the load at B?
Please answer all, Strength of Materials. Thanks!
Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation which contains that force as the only unknown. The forces are positive if in tension, negative if in compression. - 3.5 m Answers: BC= BE= A EF= 3.5 m i i i B 3.5 m 3.5 m C 2.4 m E 26.5 KN 3.5 m KN KN KN D