The square timber used as a railroad tie carries two uniformly distributed loads, each totaling 48 kN. The reaction from the ground is uniformly distributed. Determine the smallest allowable dimension b in mm of the section if the bending stress in timber is limited to 8 MPa. 0.5 m 0.2 m 1.0 m 0.2 m 0.5 m 48 kN 48 kN b

The square timber used as a railroad tie carries two uniformly distributed loads, each totaling 48 kN. The reaction from the ground is uniformly distributed. Determine the smallest allowable dimension b in mm of the section if the bending stress in timber is limited to 8 MPa. 0.5 m 0.2 m 1.0 m 0.2 m 0.5 m 48 kN 48 kN b

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 1: A member having the dimensions shown is used to resist an internal bending moment of M kNm. Determine the maximum stress in the member if the moment is applied (a) about the z axis (as shown) (b) about the y axis. Sketch the stress distribution for each case. Take: M= 98 kNm mm A= 208 mm B= 158 mm B mm Solution: The moment of inertia of the cross-section about z and y axes are 1 AB³ 12 |(10-) m* 1 ВАЗ — 12 I, |(10) m* = For the bending about z axis, c = m Mc O pax MPа Iz For the bending about y axis, c = m Mc MPа Iy max z MPa KN=M Omax Y MPa. M KN-M MPa O max Z Omax Y MPa
2 Provide Free Body Diagram, labeled with appropriate quantities to better understand. Also solve. Thank you. Please help
For the frame shown, determine the minimum bolt diameter at B if the shearstress in the bolt is 13.053 ksi
A standard truck moves across a 25- meter span. The wheel loads are P1=36 kN and P2=142 kN separated by 4.3 m and P3=142 kN at 7.6 m from P2. Determine the beam dimensions if the maximum flexural stress is equal to 100 MPa. Use the ratio h = 1.6b. Round your answer into the nearest whole number. O 213 mm x 415 mm O 415 mm x 213 mm O 321 mm x 514 mm O 514 mm x 312 mm
The beam is made from two plastic pieces glued together at the seam A. If it is subjected to the loading shown, determine the vertical shear force resisted by the flange of the beam at the critical section (in pounds). The supports at C and D exert only vertical reactions on the beam.
determine the ractions ro the supports
Determine the maximum bending stress in the handle of the cable cutter at section a–a. A force of 45 lb is applied to the handles.
The bar has a thickness of 0.5 in. and is subjected to a moment of 600 lb # ft. Determine the maximum bending stress in the bar.
3. If w=30 kN/m and L=10m, the cross section is made-up of two I-beams shown, determine the following: a. Maximum Moment if an additional 50 kN concentrated load is acting at 2 m from the right support. b. Moment of Inertia of the section about its neutral axis c. Maximum Bending stress if an additional 50 kN concentrated load is acting at 2 m from the right support. 210 mm 24 mm 15 mm 230 mm A B 24 mm
Determine the weight of the counterweight W that should be used. Calculate the shear forces and bending moments and draw the diagrams.
The simply supported joist is used in the construction of a floor for a building. In order to keep the floor low with respect to the sill beams C and D, the ends of the joist are notched as shown. If the allowable shear stress is tallow = 350 psi and the allowable bending stress is s allow = 1700 psi, determine the smallest height h so that the beam will support a load of P = 600 lb. Also, will the entire joist safely support the load? Neglect the stress concentration at the notch.
In a 2.5 cantilevered I-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress in beam is 120 Mpa, determine the section modulus and The base and height of the beam if the base is 75% of its height mm.