The spring ABC has a stiffness of 500 N/m and an unstretched length of 6 m. A horizontal force F is applied to the cord whs s attached to the small pulley B so that the displacement of the pulley from the wall is d-1.5 m. Draw a free-body dine for the small pulley B. k= 500 N/m 6 m k= 500 N/m

Q: T1 T2 A horizontal shaft having a diameter of 100 mm and a mass of 82 kg rotates in two bearings…

A:

Q: b M

A:

Q: Determine the spring constant k4 (N/m) if the extension of the whole system is 1.04 m when a force…

A:

Q: Determine R if the equivalent spring stiffness constant (keq) of the spring system is 500 N/m R N/m…

A:

Q: A spring with a constant equal to 15 KN/m is connected to points C and F of the mechanism shown in…

A: Free Body Diagram

Q: CDEFGH is plate with a circular hole in it and has a unit weight p = 2 kN/m². If the initial length…

A: Given data :- To determine :- Final length of spring

Q: etermine the equivalent torsional spring constant of the system that will be located in the position…

A: Given:k1=k2=k=1.5 N/mL=2 m

Q: The smooth surface of the vertical cam is defined in part by the curver (0.2 cos 0+0.3) m. (Figure…

A: Given Dataθ˙=4 rad/sr=0.2cosθ+0.3k=30N/mm=0.9kgθ=30°

Q: A bar is attached to the spring at the point C. The left end of the bar is pin supported and can…

A:

Q: Determine the art and y components of the reaction force on the rocker arm ABC at the pin for…

A:

Q: Neglecting the weight of all members, compute the maximum value of P that can  be applied in the…

A:

Q: For the spring assemblage shown below, Determine the displacement at node 2 and the for each spring…

A:

Q: Pulleys A and B are separated by 450 mm. The shaft has a diameter of 40 mm and is made of steel with…

A: To find: The angle of twist of pulley B relative to pulley A. Given: The distance between pulley A…

Q: applied. Use k1 - 12.67 N/m, k2 - 11.1 N/m, k3 - 28.39 N/m, and k5 - 33.91 N/m. (Use 2 decimal…

A:

Q: Consider the four bar suspension linkage shown describing the figure. Use the given dimensions from…

A: take axis as shown in fig, B=W1,h1=5.9,8.1 E=w1+W2+W3+W4+W5, h3E=5.9+4.2+6.8+4.6+7.6, 14.8E=29.1,…

Q: 3. A hinged rigid bar of length 1 =3 m (where 12=2.11-2m) is connected by two springs of stiffnesses…

A:

Q: Q-2. Form the differential equation by eliminating the arbitrary constants y = a csc z+b cot r

A:

Q: In the figure, if μ = 0.30 under both blocks and A weighs 400 lb, find the maximum weight of B that…

A:

Q: Determine the equivalent torsional spring constant of the system that will be located in the…

A:

Q: 0.51 0.8m 1.0m LCP RCP 本

A: For solution refer below images.

Q: Determine the tension in the cables AB, AC, and the displacement of the cable AB supporting a lamp…

A: Given         KAB=300 NmL=2 m

Q: C 28 KN E G 28 KN b

A:

Q: Ultimate goal: Determine the angular velocity of the pendulum when it rotates clockwise 90 degrees.

A:

Q: The 6.0-1b bar is pinned at its center O and connected to a torsional spring. The spring has a…

A: In this problem first the moment about O is taken and the acceleration is integrated to get the…

Q: the rod vertical in a stable position the minimum value of spring constant K needed is

A: GIVEN DATA; Let the weight be displaced from equilibrium position ,then

Q: The right end of a horizontal beam of mass 4kg and length 3.3m is fixed to a wall by a hinge. The…

A:

Q: Given that the force P is applied in a plane parallel to the y-z plane. e = 65°, My, = 15 Nm and Mz,…

A:

Q: Determine the equivalent spring stiffness constant of the following spring in series and parallel.…

A:

Q: Determine the displacement (m) of the whole spring system given if the net force applied to the…

A:

Q: Problem 3: μs = 0.60 between wedges B and C and us = 0.40 between the surfaces B & A and C & D. If…

A:

Q: -3 m since the space lattice system is in balance OBD determine the forces acting on the bar y 4 m 3…

A: Given, P=10 kN The coordinates of the points, O0 m, 0 m, 0 mA0 m, 4 m, 0 mB0 m, 7 m, 0 mD0 m, 7 m,…

Q: 1- The beam BD in the following mechanism has 50 kg mass with centre of gravity • G. It is supported…

A:

Q: The 8.0-lb bar is pinned at its center O and connected to a torsional spring. The spring has a…

A:

Q: Determine reaction moment at point A. 600 N 1 m 400 N 0.5 m 0.75 m 0.75 m A 500 N y

A:

Q: find the mobility and determine the Grashof condition

A: The number of links is, L=4 The number of full joints is, J1=4 The number of half joints is, J2=0…

Q: Determine the vertical displacement of point C in inches by using he method of virtual work. A is a…

A:

Q: Both rollers seen in the figure are fixed to the shaft and the shaft is quartered at a fixed angular…

A:

Q: Using the concept of torsion, determine the magnitude of the torsores at points A and B of the…

A:

Q: H, =0.40 Hz = 0.30 D 150 mm 150 mm B E 300 mm 300 mm M 150 mm 150 mm 250 mm

A:

Q: Find the torque req link AB of the mechanism shown in figure maintain the static equilibrium. F E CD…

A: The answer is in the following steps

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.