The specification of BJT transistor for model of BC107/BC108/109 from PhilipsSemiconductors is given as in Appendix A.(a)(b)Design a BJT amplifier circuit with common-emitter fixed bias configuration that hasa gain of AVL = -80. Assume r = ∞ .For the circuit designed as in Q1(a), without affecting the operating point of thetransistor, improve the circuit so that the value of AVL is doubled. Prove yoursuggestion via calculation. QUICK REFERENCE DATASYMBOLVCBOVCEOІсмPtothFEfrlove uitsPARAMETERcollector-base voltagefor-base volBC107BC108; BC109collector-emittercollector emitter voltage TI TEAL MALAYSIA MELAK45open baseBC107BC108; BC109peak collector currenttotal power dissipationDC current gainBC107BC108BC109transition frequencyCONDITIONSopen emitterTamb ≤ 25 °Clc = 2 mA; VCE = 5 VMIN. MAX.يو سيتيlc = 10 mA; VCE = 5 V; f = 100 MHz110110200100503020200300450800800UNITVVmAmWMHz

The quick reference data for the BC107, BC108, and BC109 transistors from Philips Semiconductors is…

The specification of BJT transistor for model of BC107/BC108/109 from Philips Semiconductors is given as in Appendix A. (a) (b) Design a BJT amplifier circuit with common-emitter fixed bias configuration that has a gain of AVL = -80. Assume ro = ∞ . For the circuit designed as in Q1(a), without affecting the operating point of the transistor, improve the circuit so that the value of AvL is doubled. Prove your suggestion via calculation.

The specification of BJT transistor for model of BC107/BC108/109 from Philips Semiconductors is given as in Appendix A. (a) (b) Design a BJT amplifier circuit with common-emitter fixed bias configuration that has a gain of AVL = -80. Assume ro = ∞ . For the circuit designed as in Q1(a), without affecting the operating point of the transistor, improve the circuit so that the value of AvL is doubled. Prove your suggestion via calculation.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Describe the working principles of Bipolar Junction Transistor (BJT): Study of Single Stage Transistor Common Emitter Amplifier
(iii), Why is the voltage-divider bias the preferred bias configuration? (iv) In a certain voltage-biased npn transistor, VB is 2.95 V. The DC emitter voltage is (a) 0.7 V (b) 2.95 V (c) 2.25 V (v) The emitter current is always (a) greater than the base current (b) less than the collector current (c) greater than the collector current (d) 3.65 V (d) answers (a) and (c)
Draw typical output characteristics of a common emitter npn transistor and clearly identify the active, saturation, and cut off regions on your drawing.
Subject : Electronics Engineering Draw the PNP transistor circuit in CB configuration. Sketch the output characteristics. Indicate active, saturation and cut off regions. Briefly explain the nature of these curves.
Given NPN transistor, if the base current is 10mA and the emitter current is 600mA, what would be the (a) Collector current and (b) the ratio of collector & base current beta?
c) Figure 2.3 shows the circuit diagram of a typical npn BJT common emitter amplifier. The values of RB1-30 kOhm, RB2=10.XY kOhm, Rc-3.XY kOhm, Ic=2.XY mA and Vcc=24 V. If the transistor current gain 3 = 50 determine using the full analysis and assuming VBE = 0.7 V the value of RE, hence identify the location of the Q-point (Ic, VCE, IB and VBE). Now sketch the AC circuit model of this amplifier and determine the value of the ac open circuit voltage gain Av and the ac short circuit current gain Ai. (Assume that Vth = 26 mV). Vin RB1 Cin lin RB2 -10 Rc VB RE + Vcc Vc Cout VE www li Figure 2.3 Vout Ce ¡out x=1 y=7
I need the answer quickly
Please solve all and show all the steps in detail
The value of current gain beta for a transistor is 100. if the value of emitter current is 10 mA. Determine the collector current.