The soil shown in the figure having the properties C = 0, 0 = 450, Ydry = 16kN/m³ and Ysat 20kN/m. What should be the depth of ground water table (GWT) from the surface of the soil to achieve a factor of safety (FOS)= 2 of an infinite soil slope shown in the figure. Take Yw= 10 kN/m³ 10 m 25° matunton GWT

The soil shown in the figure having the properties C = 0, 0 = 450, Ydry = 16kN/m³ and Ysat 20kN/m. What should be the depth of ground water table (GWT) from the surface of the soil to achieve a factor of safety (FOS)= 2 of an infinite soil slope shown in the figure. Take Yw= 10 kN/m³ 10 m 25° matunton GWT

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A soil profile is shown in Figure Q. Given: Layer I – H, = 3 m, Ya = 15 kN/m³; Layer II – H, = 4 m, Ysat = 16 kN/m³; Layer III – H3 = 5 m, Ysat = 18 kN/m³. Plot the variation of a, u and o' with depth. %3D A Layer I Groundwater table H2 Layer II H3 Layer III Figure Q : Dry sand Sand Clay Rock
A SOIL PROFILE HAS 2 DIFFERENT LAYERS OF SOIL. SOIL 2 WITH sg = 2.72 AND MOISTURE CONTENT = 60%, IS OVERLAIN BY SOIL 1 WITH sg = 2 AND MOISTURE CONTENT = 0.65. IF THE WATER TABLE IS INITIALLY ON THE GROUND SURFACE, FIND THE TOTAL STRESS AT THE MID-HEIGHT OF SOIL 2 IF THE WATER TABLE HAS TO BE LOWERED BY 2m. SOIL 1AND 2 HAS HEIGHT 3m EACH. * Your answer
The soil profile at a site up to a depth of 10m is shown in the figure (not drawn to the scale). The soil is preloaded with a uniform surcharge (q) of 70 kN/m2 at the ground level. The water table is at a depth of 3 m below ground level. The soil unit weight of the respective layers is shown in the figure. Consider unit weight of water as 9.81 kN/ m3 and assume that the surcharge (q) is applied instaneously. q = 70 kN/m? Ground level 3m Sand (Bulk unit weight = 18 kN/m³), Ground water table Silty clay (Saturated unit weight = 20 kN/m) 4m. 3m Clay (Saturated unit weight = 21 kN/m) Boulder clay Immediately after preloading, the effective stresses (in kPa) at points P and Q, respectively are
For a soil the following is given: wet specific weight 19.21 kN / m3, water content w = 19.2%, S = 60%. Determine: a) Porosity n b) Dry specific gravity , c) List of voids e, d) Gs e) Amount of water for complete saturation. Make the schematic.
Herbaceous vegetation is used to protect and stabilize the slope. As shown in the figure, try to calculate the stability and safety factor FS=?It is known that c'=effective soil cohesion (t/m^2); θ=effective soil friction angle; ▲c'=effective soil cohesion due to root system increase (t/m^2); r1=soil above groundwater level Unit volume weight (t/m^3); r2 = unit volume weight of soil below the groundwater level (t/m^3); Ws = total weight of abcd soil above the potential sliding surface (t/m)
2. SPT test was performed at a shallow site composed of uniform granular soil with a unit weight = 20 kN/m³ (shown below are N60). a) Convert to (N1)60. b) Estimate the range of friction angles at depths between 20 and 40 ft. Use various correlations. Compare the differences. SPT N-values (bpf) 10 20 30 40 50 10 Silty Sand (SM): Piedmont Residuum 30 40 50 60 Depth (feet)
Q2. A soil profile consisting of three layers is shown in Figure 1 below. Unit weight of water (yw) = 9.81 kN/m³ Layer no. 1 2 3 ↑ H₁ H₂ Dry sand Sand Clay Rock Figure 1: Soil Profile Thickness H₁ = 1.5 m H₂ = 2.53 m H3 = 2.64 m Layer 1 Groundwater table Layer 2 Layer 3 Soil parameters Yd = 16.5 kN/m³, Ysat = 17.42 kN/m³ Ya = 16.5 kN/m³, Ysat = 18.55 kN/m³ Yd = 17.50 kN/m³, Ysat = 19.23 kN/m³ a) Calculate the values of o, u and o' at points A, B, C and D. b) Calculate the effective stress at C when water table drops by 2 m. c) Calculate the effective stress at C when water table rises by 1 m above layer 1 due to flooding.
EXAMPLE 9.8 A soil profile is shown in Figure 9.24. Given: H₁ Plot the variation of o, u, and o' with depth. H₁ H₂ B Zone of capillary rise G₁ = 2.66; e = 0.55 Degree of saturation = S = 50% Sand Saturated clay = 2 m, H₂ = 1.8 m, H3 = 3.2 m. Rock G₁ = 2.66 e = 0.55 Sand Groundwater table w 42% (moisture content) G₁ = 2.71 Clay
5-4 For the given soil profile and the piezometric surfaces measured at the top of the two sand and gravel layers, determine the pore pressure and effective stress at points A, B, C, D, and E. Piezometers 2 m Ground surface 2 m Sand y = 18 kN/m3 Water table y_ 11m Y = 20 kN/m3 A 4 m Clay Y = 18 kN/m3 加。B 1Im 5 m Sand and gravel y = 22 kN/m3 2 m •D 5 m Clay Y = 19 kN/m3 Sand and gravel y = 23 kN/m3 %3D Cpyright by
Q: Explain the stress vs. time and settlement vs. time relationships for a soil layer under stress increase pf indicating the compensation of surcharge as shown in the figure below ignoring the secondary compression. Subject: ground improvement techniques Program: civil transportation engineering
Problem 4: Total stress, pore pressure and effective stress A soil profile is shown in the following figure. Calculate the total stress, pore water pressure and effective stress at points A, B, and C. 6m 13m B Dry sand Saturated sand Clay Dry sand Ydry 16.5 kN/m³ Groundwater table Saturated sand Ysat 19.25 kN/m³ =