The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.“]. Assume that the support at D can provide resistance either up or down. For a loading of w = 4.5 kips/ft, determine: (a) the beam deflection vĄ at point A. (b) the beam deflection vc at point C. Assume LAB= 11 ft, Lác= 9 ft, LcD= 9 ft, LDE= 6 ft. A E LAB LBC Lcd Lpe Answers: (a) VA = in. (b) vc = in.

The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.“]. Assume that the support at D can provide resistance either up or down. For a loading of w = 4.5 kips/ft, determine: (a) the beam deflection vĄ at point A. (b) the beam deflection vc at point C. Assume LAB= 11 ft, Lác= 9 ft, LcD= 9 ft, LDE= 6 ft. A E LAB LBC Lcd Lpe Answers: (a) VA = in. (b) vc = in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Strength of material
Assuming that E=200 GPa and I=2.63x108 mm4, determine the total force P exerted by the 25 mm diameter, 2m long steel rod at B.
The column is constructed of a steel wide-flange section (W 8 x 28) hav- ing modulus of elasticity E = 29 x 10³ ksi and proportional limit σpl = 42 ksi. The total length of the column is L = 25 ft. Determine the allowable load Pallow using a factor of safety n = 2.5 with respect to Euler buckling of the column. X B P X L 2 = 12.5 ft = 12.5 ft 2 W 8 X 28 1 2 Section X-X
KINDLY HELP ME WITH THIS PLEASEEEE
Maximum Deflection Calc
The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E - 29,000 ksi; I - 843 in."1. Assume that the support at D can provide resistance either up or down. For a loading of w- 6.7 kips/ft, determine: (a) the beam deflection Va at point A. (b) the beam deflection vç at point C. Assume LaB = 8 ft, Lec=6 ft, Lco- 6 ft, Log = 7 ft. B. LAB Lạc Lep LDE Answers: (a) va- in. (b) vc- in.
A rectangular beam has a width b = 300 mm, and effective depth d = 500 mm and a total height h = 550 mm. The beam is reinforced with three bars ᶲ 20 mm. Compute the nominal strength of the beam cross section Mn and the design moment Mu. Use f’c = 35 MPa and Fy= 420 MPa.
FOLLOW INSTRUCTIONS AND WITH FBD FOR UPVOTE THANKS. DO AMM ONLY. DO AMM ONLY
The frame shown below is subjected to an applied Point Load of 27kN and a Uniformly Distributed Load of 3kN/m and is supported at A by a pinned connection and at B by a roller connection. Calculate the vertical support reaction at B. Give your answer in kN to 2dp. 3m 3m PL UDL 5m A
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression. Assume F-2770 N, a-2.1m, b-4.2 m, 0 = 48% Answers: AB- AC- AD- BC- B CD i i i b 8 N N N N N
For the beam below, determine the following, assume EI is constant. What is MBA in k-ft? O Select the correct response: C 108 -72 72 2 k/ft -180 24ft
Determine the positive nominal flexural strength Mn of the T-beam in the figure below. Assume fc′ = 21MPa and fy = 420MPa Determine the effective width of the flange if the clear spacing of the beams is 2m while the clear span length of the beam is 3m. Determine the Nominal Moment Capacity of the beam considering that the diameter of stirrup is 10mm and the concrete cover is at 40mm.