Assuming that E=200 GPa and I=2.63x108 mm4, determine the total force P exerted by the 25 mm diameter, 2m long steel rod at B.

Q: a) Determine the normal force at point D. Express your answer in kilopounds to three significant…

A:

Q: P 3 m * 3 m 50 mm 50 mm 20 mm 20 mm 150 mm N/A A The T-shaped beam shown above is supporting a…

A: Maximum bending stress is given by σmax= MmaxI*ymax  locate the Neutral axis from bottom we have y =…

Q: A force P of magnitude 1,100 N is applied to the pedal shown satisfies a shearing stress in the pin…

A: Take moment about C∑ Mc=0TBA0.125-11000.3=0TBA=2640N∑ Fx=0TBA-Cx=0Cx=2640N∑ Fy=0 Cy=1100N…

Q: Consider the beam shown below. Take P = 5 kip and w = 1.7 kip/ft. Point E is just to the right of…

A: Solution:Given Data:The concentrated load acting on the beam is P=5kipThe intensity of uniformly…

Q: Can you explain in detal why the moment about x is -0.450(150)? from my point of view it should be…

A: See the explanation given below. Explanation:Step 1: Step 2: Step 3: Step 4:

Q: Question 1. Determine the tension force in member C and its angle e for equilibrium. The forces are…

A:

Q: Compound axial member ABC has a uniform diameter of d = 3.0 in. Segment (1) is an aluminum [E₁ =…

A:

Q: The rigid bars AC and BCD are supported by pins at A and B and by a steel rod at D. There is a…

A:

Q: * the frame below, F = 9.7 kips, a = 6 ft, b = 5 ft, and c= 5ft Determine the magnitude of the…

A: F = 9.7 kips, a = 6 ft, b = 5 ft, and c = 5 ft To find: The magnitude of horizontal force at B

Q: Rod BD is made of steel (E= 29 x 106 psi) and is used to brace the axially compressed member ABC.…

A: the rod BD is made of steel EBD=(29 x 106) psi= (29 x 103) ksi and it is used to brace the axially…

Q: 5. The beam shown is resting on two moveable supports. It carries a uniform love load of 140 N/m and…

A:

Q: For the bar in the figure, with an quadrangular cross section, determine the maximum shear stress…

A:

Q: force P in the xy-plane acts on the triangular plate. Determine P in the following situations:a)…

A:

Q: Consider the beam shown in (Figure 1). Suppose that wi = 600 N/m, w2 = 300 N/m. Follow the sign…

A:

Q: For the frame below, F = 9.9 kips, a = 3 ft, b = 5 ft, and c = 3 ft. Determine the magnitude of the…

A:

Q: 2 kN/m 10 kN 5 kN 1 kN/m B 2 m 2 m 3.

A:

Q: Compound axial member ABC has a uniform diameter of d = 1.2 in. Segment (1) is an aluminum [E₁ =…

A:

Q: A vertical steel bar ABC is pin-supported at its upper end and loaded by a force P1 at its lower…

A: Given:-  P1 = 2.5 kip, P2 = 1 kip, and M = 25 kip-in. The modulus of elasticity is E = 29,000 ksi…

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.