The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; /= 843 in.4]. Assume that the support at D can provide resistance either up or down. For a loading of w = 6 kips/ft, determine: (a) the beam deflection VA at point A. (b) the beam deflection vc at point C. Assume LAB = 13 ft, LBC= 8 ft, LcD=8ft, LDE = 5 ft.

The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; /= 843 in.4]. Assume that the support at D can provide resistance either up or down. For a loading of w = 6 kips/ft, determine: (a) the beam deflection VA at point A. (b) the beam deflection vc at point C. Assume LAB = 13 ft, LBC= 8 ft, LcD=8ft, LDE = 5 ft.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Need help!
The simply supported beam consists of a W21 × 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.4]. Assume that the support at D can provide resistance either up or down. For a loading of w = 7.8 kips/ft, determine:(a) the beam deflection vA at point A.(b) the beam deflection vC at point C.Assume LAB = 10 ft, LBC = 8 ft, LCD = 8 ft, LDE = 7 ft.
J- A distributed load op w (kulm) is applied over the entire tength OF a simply supported beam Gm long . The beam section is as shown. Determine the maximum value OF w iF Of Ś 1OMP , and yE 800KP. 80 mm X 200 mm 360mm 200mm
PLEASE ANSWER ASAP THANK YOU
Correct answer.
The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I=843 in.4]. Assume that the support at D can provide resistance either up or down. For a loading of w = 6.6 kips/ft, determine: (a) the beam deflection VA at point A. (b) the beam deflection vc at point C. Assume LAB = 10 ft, LBc = 7 ft, LcD = 7 ft, LDE = 6 ft. W B Answers: (a) VA = (b) vc= LAB LBC C in. in. D LCD O LDE E
Determine the positive nominal flexural strength Mn of the T-beam in the figure below. Assume fc′ = 21MPa and fy = 420MPa Determine the effective width of the flange if the clear spacing of the beams is 2m while the clear span length of the beam is 3m. Determine the Nominal Moment Capacity of the beam considering that the diameter of stirrup is 10mm and the concrete cover is at 40mm.
Use conjugate beam only
i need the answer quickly
The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa; I = 370 x 106 mm*). For the loading shown, determine the beam deflection vc at point C. Assume P = 56 kN, w = 22 kN/m, Lag = Lsc= 2.9 m, Lco = 2.9 m. LAB LBC LCD Answer: Vc= mm.
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a=lm, b= 1.75m, d=50 mm, h= 6mm E D 2a b
Use conjugate beam only