The shaft is made of L2 tool steel, has a diameter of 40 mm, and is fixed at its ends A and B. (Figure 1) It is subjected to the torque T = 1.7 kN-m. Figure A T 800 mm B 600 mm. 1 of 1 Part A Determine the maximum shear stress in region AC. Express your answer to three significant figures and include appropriate units. (Tmax) AC= Value Submit Part B μÀ Request Answer Submit (Tmax) BC= Value Determine the maximum shear stress in region CB. Express your answer to three significant figures and include appropriate units. HÅ < Return to Assignment Request Answer 6 Units + ? Units Provide Feedback C IWC ?

The shaft is made of L2 tool steel, has a diameter of 40 mm, and is fixed at its ends A and B. (Figure 1) It is subjected to the torque T = 1.7 kN-m. Figure A T 800 mm B 600 mm. 1 of 1 Part A Determine the maximum shear stress in region AC. Express your answer to three significant figures and include appropriate units. (Tmax) AC= Value Submit Part B μÀ Request Answer Submit (Tmax) BC= Value Determine the maximum shear stress in region CB. Express your answer to three significant figures and include appropriate units. HÅ < Return to Assignment Request Answer 6 Units + ? Units Provide Feedback C IWC ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

answers stated in box are incorrect
Mechanical design The maximum load in a rotating shaft is subjected to bending moment of 1 kN.m and a torque of 1 kN.m. The member is made of steel the Ultimate Tensile Strength 440 MPa, Yield Tensile Strength 370 MPa. With a safety factor of 4, kt = km = 1.5 and keyway stress consternation is presented. According to the maximum shear stress theory, the shaft diameter will be: a. 160 mm b. 74 mm C. 145 mm d. 92.5 mm e. 60 mm f. 66 mm
Part A The lever is attached to the shaft A using a key that has a width d and length of 26 mm .If the shaft is fixed and a vertical force of 200 N is applied perpendicular to the handle, determine the dimension d if the allowable shear stress for the key is T = 37 MPa (Figure 1) Express your answer with the appropriate units. HA d = Value mm Submit Request Answer Provide Feedback Next > Figure d -20 mm 500 mm 200 N
Dr. (ny) A = 5.52 تمارين : واجب بيتي 1. The solid steel shaft 100 mm in diameter and 8 m long was made of AISI 1020 HR steel is subjected simultaneously axial to an compressive force of 200 kN and a torque T. find the maximum applied torque T depending on the maximum shear stress, if the factor of safety is 1.5 and Ssy === Sy (Neglect buckling) 600 kN 30 T 100 mm 600 kN Prepared by Dr. Hazim Khale anc dir the dia BC (b to ca th th n
II kN m 5 kN m 3 kN m 3 kN m 75 mm 85 mm 70 mm 2 m 2m 2 m FIGURE P12-6 The "new" magnitude of the external torque applied at "B" to maintain equilibrium of the shaft is ---_kN-m. The magnitude of the minimum shear stress in the shaft between "A" and "B" is MPа. The magnitude of the maximum shear stress in the shaft between "A" and "B" is _____MPa. The magnitude of the maximum shear stress in the shaft between "B" and "C" is MРа. The magnitude of the maximum shear stress in the shaft between "C" and "D" is _____MPa. The magnitude of the minimum shear stress in the shaft between "C" and "D" is __--_MPa. 10
2. An implant is made of a titanium alloy having an allowable shear stress of tallow = 50 MPa. If the diameter of the implant is 120 mm, determine the maximum torque T that can be transmitted. What would be the maximum torque T' if an 80-mm-diameter hole were bored through the implant? 1S T (Answer: T =16.96 kN.m; T'=13.613 kN.m)
i need the answer quickly
Given: l1=1,3l; l2=1,9l; l3=1,2l; M1=-0,6M; M2=-1,6M; M3=1,9M. Parameter of length l=40cm; cross section diameters: d=41mm; d0=26mm. The shaft is made of steel with yielding shear stress τY=250MPa; factor of safety n=1,6. Find: the allowable value of load parameter (in Nm) MA = ?
Carefully solve.
QUESTION 5 The solid shaft as shown in Figure 5 is made of material that has an allowable stress of [X(45)+20]MPa. Determine the required diameter of the shaft to the nearest mm. Given the value of X=7 and Y=5 15 N-m 25 N-m 30 N-m Figure 5 60 N-m 70 N-m
A mectal cylinder of 5 cm in diameter and initially at a temperature about 150 °C. the eylinder is suddenly immersed in liquid with temperature at 50 °C and heat transfer coeflicient about 2000 W/m.°C. Under typical operation conditions the center temperature and surface temperature are measured to be 110 °C and 90 °C after 1 minute, respectivielly. Calculate the thermal conductivity for this material.
The nodal point on the shaft section is subjected to opposed shear stress, this leads to decrease in the effect of torsional shear stress which increases the fatigue life of the shaft. Select one: O True O False