The shaft is made of A-36 steel, It has a diameter of 28 mm and is supported by bearings at A and D which allow free rotation. The shear modulus of elasticity for A-36 steel is 75 GPa (Figure 1) Part A Determine the angle of twist of gear C with respect to B. Express your answer using three significant figures. vec OC/B = rad Submit Request Answer Figure < 1 of 1 Provide Feedback 90 N-m 0.6 m 90 N-m 0.75 m 0.9 m

The shaft is made of A-36 steel, It has a diameter of 28 mm and is supported by bearings at A and D which allow free rotation. The shear modulus of elasticity for A-36 steel is 75 GPa (Figure 1) Part A Determine the angle of twist of gear C with respect to B. Express your answer using three significant figures. vec OC/B = rad Submit Request Answer Figure < 1 of 1 Provide Feedback 90 N-m 0.6 m 90 N-m 0.75 m 0.9 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Knowing that the average normal stress in member EF of the Pratt bridge truss shown must not exceed 8.99 ksi for the given loading, determine the cross-sectional area (in sq. in) of this member that will yield the most economical and safe design if h = 11.7 ft and P = 92.21 kips. Round off the answer to five decimal places. 010.png В D F h H C E G -on-- 9 ft→9 ft→9 ft→-9 ft- P P
pls reply
The lap joint is connected together using a 32 mm diameter bolt. Determine the permanent shear strain in the shear plane of the bolt when the applied force P = 750 kN is removed. Note: The bolt is made from a material having a shear stress-strain diagram as follows T (MPa) A { 600 400 5 50 y (10³ rad)
Q1: If the beam with T section shown in Figure 1 is subjected to a positive bending moment so N.m Use the data úio fihgimiazmniarmmand do iim) from Table 1, determine the following: 1. The location of the centroid measured from the top fiber in (mm) 2. The moment of inertia about the centroidal x axis (mm*) 3. The maximum compressive stress in (MPa) 4. The maximum tensile stress in (MPa) 110mm 27mm 37mm 27mm Figure 1
In figure shown below B 960 Imm 640 N 3 280 mm 960 N a. Determine the tension in segment AC b. Determine the tensibn in segment BC
Consider the girder and the moving loads shown in (Figure 1). Suppose that P= 80 kN. Figure A 6 m C 10 m 60 kN 30 kN B 2 m/ 30 kN m 1 of 1. ▼ Part A - Determine the maximum live bending moment at C caused by the moving loads. Follow the sign convention Express your answer to three significant figures and include the appropriate units. (Mc)max 710 Submit = μA Provide Feedback kN m Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining ? D
Figure Consider the truas shown in (guce. Suppose that F-9 kN. Assume all members are pin connected. M 1 of 1 Part A Determine the force in the member ED and state if the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FED- Submit Part B Submit HÅ Value Fon= Value Provide Feedback Request Answer A Units Request Answer Determine the force in the member CD and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the c compression and positive value in the case of tension. G ? Units 85 0009 3: ? .. Pas S C LE
A solid brass E= 100 GPa axial member is loaded and supported as shown in the figure. Segments (1) and (2) cach have a diameter of 22 mm and segment (3) has a diameter of 14 mm. Carrying loads W1 - 37 kN, W2 = 14 kN, and W3 = 25 kN, at their respective positions shown on the figure below. Determine the deformation of segment (2) in MPa. Answer should be rounded up to the nearest 3 decimal places. (1) WI W2 W3
A rigid bar is attached to two vertical rods before a load is applied. Compute the vertical movement under P= 50kN *DRAW THE FBD; COMPLETE SOLUTION *USE 3 DEC PLACES
The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point P (very close to the bottom of the flange) is 12 MPa. The stress at point Q In the web (very close to the flange) is: N'-. 100- P Q 201 100- T 20 81484 80 20 40 --N (a) Indeterminable due to incomplete data (6) 60 MPa (c) 18 MPa (d) 12 MPa 068
Y Suppose that P = 250 lb. (Figure 1) Figure T T301-381-38- W 481 46 Part C FBC = Part D Submit Request Answer FBD= Part E FCD= Submit Part F FCE= Submit Determine the force in member of the truss. Express your answer in pounds to three significant figures. Enter negative value in the case of compres the case of tension. Part G FDE= Part H - ΑΣΦ It vec Determine the force in member BD of the truss. Express your answer in pounds to three significant figures. Enter negative value in the case of compressi the case of tension. FDF= 17 ΑΣΦ Submit Part I 1 of 1 > Request Answer Submit Request Answer FEF= ΓΙ ΑΣΦ 11 Eved Submit - Η ΑΣΦΙ Request Answer Determine the force in member CD of the truss.. Express your answer in pounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension. -- ΑΣΦ Ivec Request Answer 17 ΑΣΦ 4 Part A 5 Request Answer it vec Determine the force in member AB of the truss Express your answer in pounds to…
The shaft is made of A992 steel. It has a diameter of 0.7 in. and is supported by bearings at A and D, which allow free rotation. The shear modulus of elasticity for the material is 11 × 10³ ksi. 2 ft < 5 of 7 Part A B 2.5 ft > 60 lb-ft C 3 ft O 60 lb-ft