The shaft as shown in the figure is supported by bearings at A and B. The bearings exert only vertical reactions. The pulley wheel on the end of the shaft applies a vertical force F = 18.0 kN. What is the max shear force in the shaft? Input your answer as a value only in kN to one decimal place without +/- sign. B A 800 mm F 250 mm

The shaft as shown in the figure is supported by bearings at A and B. The bearings exert only vertical reactions. The pulley wheel on the end of the shaft applies a vertical force F = 18.0 kN. What is the max shear force in the shaft? Input your answer as a value only in kN to one decimal place without +/- sign. B A 800 mm F 250 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.13P: Figure (a) shows the cross section of a column that uses a structural shape known as W867...

See similar textbooks

Similar questions

I am struggling with this question
= Consider a hollow circular shaft of inner radius r; = 1.25 inch and outer radius of ro 1.50in, subjected to the following loads Fx = 100 lb, Fy = 150 lb, and F = 100 lb. Determine the state of stress (3x3 matrix) and the principal stresses at point p. Report your answers in psi to one decimal place. Note the figure is not to scale. у P fixed support R1-25 in 90⁰ X 90⁰ R2=50 in h=20 in Fy Note the hollow circular shaft lies in the x-y plane only Fz Fx ro ri || = /1.50" 1.25" YZ cross-section р X
In your response, please display the full computation and all FBDs that were used. Only round off at the final answer with 4 decimal places. P=2kN, F=3kN, and moment M=0.5kN-m are acting on the structure in the illustration. A pin at Z and a cable RQ connected by a connecting pin R support it. Im ● F ● P S TO M Im R lu W OZ a' 0.8m 3m If the pin support Z's factor of safety against shear stress is 3, determine whether a single or double shear should be provided for an economical and safe design. 4 m The mas allowable shear stress in the pin is 50MPa. Consider the following specifications. Single shear design: 25mm pin diameter Double shear design: 17mm pin diameter
There is a 1000N force applied on the shaft at point A. What is the normal force at B that results? Point C is meant to be a hinge. The diameter of the shaft from A to C is 25 mm, and the smaller piece of the shaft that applies force at B has a diameter of 19 mm. I dont hink those are needed though.
One shaft is in torsion as shown below. If the magnitude of shear stress at point A is 345.6 MPa, calculate the magnitude of the shear stress at point B on the same cross-section as point A: MPa. Calculate your answer to 1 decimal place. 40 mm 30 mm T
S00 Ib In the fig. shown, compute the ff: (16-18) the resultant using cosine law (force polygon) 60 R = 35 (19-20) the angle of the R measured 500 lb cW from the x- axis.
Need help with this Q.
correct ans
The hollow shaft used in the system has the following conditions: Outer Ø:110 mmØ Allowable Shearing Stress:85 MPa Determine the thickness (mm) of the shaft. Round to the nearest whole number for the thickness and use 2 decimal places for other solved values. Provide a torque diagram, strictly follow instructed sign convention, and start from left to right.
I need handwritten and correct pls if not handwritten I'll dislike
The bearings at A and B exert only x and z components of force on the steel shaft. a) Draw shear, moment and torque diagrams displaying values at each section of interest (A, B and Gear points). b) Determine the shaft's diameter to the nearest integer millimeter (Roundup) so that it can resist the loadings of the gears without exceeding an allowable shear stress Tall- Fx A 75 mm 50 mm 150 mm 350 mm B F, 250 mm Fx=15KN,Fz=22.5kN,allowable shear stress=90MPA
why the expert here wrote -200 cos 75 when Σ Fx = 0 , I understand all steps but how he got - 200 cos 75 ( for the force ) (how the angle is 75 ) can you please clarify for me this point please ...... because I did not got the angle 75 dgree for 200 N force can you draw a diagrm for me please to see how 75 dgree links to 200 N