The section of a prestressed hollow core slab is shown in Figure-2. The slab is simply –supported over a 200 mm span of 7.5 m and carries a superimposed dead load (excluding self –weight) of 1.7 kPa and live load of 2.0 kPa . The total prestressing force is 570 kN at eccentricityof 40 mm. Assume loss of prestress of 18% at service loads. The properties of the section areas follows:Cross - sectional area = 120 x 10° mm²Moment of Inertia, Ix = 312 x 10 mmMoment of Inertia, ly = 199 × 10 mm*Weight of Beam = 2.40 kPaa. Determine the stress at the bottom fibers of the midspan due to the total load in MPa.b. Determine the stress at the top fibers of the midspan due to the total load in MPa.c. What maximum uniform load (in kN/m) can the slab carry if the maximum allowablecompressive stress is 17.6 MPa and the maximum allowable tensile stress in concrete is 2.8MPa?1500 mm200 mmFigure-2

P = 570KN e = 40mm D.L = (2.4+1.7) =4.1 KPa L.L = 2KPa y = 200/2 = 100mm A(area) = 120x103 mm2

The section of a prestressed hollow core slab is shown in Figure-2. The slab is simply – supported over a 200 mm span of 7.5 m and carries a superimposed dead load (excluding self – weight) of 1.7 kPa and live load of 2.0 kPa. The total prestressing force is 570 kN at eccentricity of 40 mm. Assume loss of prestress of 18% at service loads. The properties of the section are as follows: Cross - sectional area = 120 × 10° mm Moment of Inertia, Ix = 312 × 10° mm* Moment of Inertia, ly = 199 × 10° mm Weight of Beam = 2.40 kPa a. Determine the stress at the bottom fibers of the midspan due to the total load in MPa. b. Determine the stress at the top fibers of the midspan due to the total load in MPa. c. What maximum uniform load (in kNm) can the slab carry if the maximum allowable compressive stress is 17.6 MPa and the maximum allowable tensile stress in concrete is 2.8 MPa? 1500 mm 200 mm

The section of a prestressed hollow core slab is shown in Figure-2. The slab is simply – supported over a 200 mm span of 7.5 m and carries a superimposed dead load (excluding self – weight) of 1.7 kPa and live load of 2.0 kPa. The total prestressing force is 570 kN at eccentricity of 40 mm. Assume loss of prestress of 18% at service loads. The properties of the section are as follows: Cross - sectional area = 120 × 10° mm Moment of Inertia, Ix = 312 × 10° mm* Moment of Inertia, ly = 199 × 10° mm Weight of Beam = 2.40 kPa a. Determine the stress at the bottom fibers of the midspan due to the total load in MPa. b. Determine the stress at the top fibers of the midspan due to the total load in MPa. c. What maximum uniform load (in kNm) can the slab carry if the maximum allowable compressive stress is 17.6 MPa and the maximum allowable tensile stress in concrete is 2.8 MPa? 1500 mm 200 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

0.11
For a simply supported prestressed concrete beam, compute the stress in the top fiber at the centerline. Properties of the bearn are: Width of the bearm, b: 326 mm; Depth of the beam, d: 471 mm; Eccentricity of the beam, e: 157 mm; Prestressing Force, P: 739 KN; Superimposed Load, w: 6 KN/m; Length of the beam, L: 9 m. Stress is in unit MPa. Write only the value of your final answer. w (including selfweight) P. P.
3. A circular steel bar with cross sectional area of 4 in is loaded as shown. a) Compute the shear and tensile stresses at plane X-X when 0 = 30°. b) Indicate at which angle(s) shear stress is maximum. c) Also, calculate the maximum compression stress and indicate the angle at which this maximum compression stress Occurs. 10,000 lb 10,000 lb
Cross sectional area and section modules of a short hollow Cl column section are 200 cm2 and 2x 10^6 mm3 respectively. It carries an axial load of 400 KN and a load of 100 KN on a bracket. The load line being 250 mm away from axis of column. Minimum and maximum stress intensities are respectively- 11:16 PM FF: 10:
Prestressed hallow core slabs with typical section shown are used for flooring of a library. Properties of the slab are as follows: A = 14 x 105 mm?; S, = S, = 6.8 × 10€ mm?; a = 1.2 m; b = 200 mm. The slab is prestressed with 920 kN force at an eccentricity e = 63 mm below the neutral axis of the section. Slab weight is 2.7 kPa, superimposed DL = 2.0 kPa; LL = 2.9 kPa. The slab is simply supported on a span of L = 8 m. Allowable stresses at service loads are 3.2 MPa in tension and 15.5 MPa in compression. Consider 20% loss of prestress at service loads. 1. Compute the maximum compressive stress (MPa) in the slab due to initial prestress force. A. 2.54 B. 12.6 C. 1.95 D. 15.1 2. Determine the maximum stress (MPa) at the bottom of the slab due to service loads and prestress force. A. 1.35 T В. 9.17 C c. 1.35 C D. 9.171 3. Determine the maximum additional load (kPa) including its own weight, that the slab can be subjected to if the allowable stresses at service loads are not to be…
An aluminum alloy pipe with an outside diameter of 4.3 in. and a wall thickness of 5/16 in. cantilevers upward a distance of L = 22 ft. The pipe is subjected to a wind loading that increases from wA = 8 lb/ft at its base to wB = 12 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe?
25 mm 0.5 m 200 mm 100 mm 100 kN -1.5m 25 mm 150 mm 25 mm 100 kN 0.5 m PROBLEM 4.10 Two vertical forces are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam.
For a simply supported prestressed concrete beam, compute the stress in the top fiber at the centerline. Properties of the beam are: Width of the beam, b: 222 mm; Depth of the beam, d: 396 mm; Eccentricity of the beam, e: 177 mm; Prestressing Force, P: 541 KN; Superimposed Load, w: 8 KN/m; Length of the beam, L: 11 m. Stress is in unit MPa. Write only the value of your final answer. w (including selfweight) 000
Hand written please