An aluminum alloy pipe with an outside diameter of 3.2 in. and a wall thickness of 3/16 in. cantilevers upward a distance of L = 20 ft. The pipe is subjected to a wind loading that increases from WA= 14 lb/ft at its base to we = 21 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe? WB WA B L

An aluminum alloy pipe with an outside diameter of 3.2 in. and a wall thickness of 3/16 in. cantilevers upward a distance of L = 20 ft. The pipe is subjected to a wind loading that increases from WA= 14 lb/ft at its base to we = 21 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe? WB WA B L

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A large spherical tank contains gas at a pressure of 430 psi. The tank is 41 ft in diameter and is constructed of high-strength steel having a yield stress in tension of 82 ksi. Determine the required thickness of the wall of the tank if a factor of safety of 3.0 with respect to yielding is required.
X Your answer is incorrect. The copper pipe [G - 7,000 ksi] has an outside diameter of 3.250 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t- 80 lb-ft/ft along its entire length. Using a - 2.0 ft, b- 3.5 ft, and c- 7.0 ft, determine (a) the maximum shear stress in the pipe. (b) the rotation angle oc at the free end of the shaft. B Answers: (a) Tmax- i 10080 ksi (b) oc - i 2045.71 rad
The vertical portion of the press shown consists of a rectangular tube of wall thickness t = 10 mm. Knowing that the press has been tightened on glued wooden planks until P = 33 kN, determine the stress at (a) point 4, (b) point B. GA OB MPa MPa 200 mm 80 mm 80 mm Section a-a 60 mm B
suppo W given that the top edge of the pipe must have zero stress at the section where the [8,022; 41,23 k
I need to solve this question for civil eng dep.
A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate shears a determine the minimum force P required to punch the slot. Punch O 1051 KN O 766 kN O 649 kN O 717 KN O 979 KN Slug Plate 20 mm 75 mm Plan view of slug + a stress of 360 MPa,
a.) What is the normal force distributed to Stainless Steel Solid Post 'A' (in kips)? b.)What is the normal force distributed to Red Brass Hollow Tube 'B' (in kips)? c.)What is the normal stress produced in Stainless Steel Solid Post 'A' (in psi)? d.)What is the normal stress produced in Red Brass Hollow Tube 'B' (in psi)?
Kindly quick as possible
A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A makes an angle of 14 degrees with respect to the horizontal axis (x-axis). a. Determine the normal stress at section A-A. b. Determine the shear stress at section A-A.
(32 H.W Find longitudinal and hoor tensile stresses in the Wall of vessel Shown in figure, if the internal pressure. is 0.9 MPa and thickness of Wall is 6.4mm ? Ans: 6 = 42.19 MP₂ °H = 62.8 Mra 4 Also find I ?=0.67 Alir G 0.6m fot TE L = 1.8m O 7 0.6m
3. A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A makes an angle of 14 degrees with respect to the horizontal axis (x-axis). a. Determine the normal stress at section A-A. b. Determine the shear stress at section A-A. 300 kN A V 300 kN
ASAP NEED RIGHT COMPLETE SOLUTION !!!