An aluminum alloy pipe with an outside diameter of 3.5 in. and a wall thickness of 2/16 in. cantilevers upward a distance of L = 19 ft.The pipe is subjected to a wind loading that increases from WA= 14 lb/ft at its base to wg = 21 lb/ft at its tip.(a) Compute the maximum value of Q for the pipe.(b) What is the maximum vertical shear stress in the pipe?WBBAnswer:(a) Qmax"(b) Tmax=Lin.3psi

Answered: Image /qna-images/answer/aed64a39-bee1-4b04-86a9-d8ab84725463.jpg

An aluminum alloy pipe with an outside diameter of 3.5 in. and a wall thickness of 2/16 in. cantilevers upward a distance of L = 19 ft. The pipe is subjected to a wind loading that increases from W₁ = 14 lb/ft at its base to wg = 21 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe? WB B Answer: (a) Qmax= (b) Tmax= L in 3 psi

An aluminum alloy pipe with an outside diameter of 3.5 in. and a wall thickness of 2/16 in. cantilevers upward a distance of L = 19 ft. The pipe is subjected to a wind loading that increases from W₁ = 14 lb/ft at its base to wg = 21 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe? WB B Answer: (a) Qmax= (b) Tmax= L in 3 psi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An aluminum alloy pipe with an outside diameter of 4.9 in. and a wall thickness of 2/16 in. cantilevers upward a distance of L = 20 ft. The pipe is subjected to a wind loading that increases from WA = 8 lb/ft at its base to WB =12 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe?
An aluminum alloy pipe with an outside diameter of 5.7 in. and a wall thickness of 5/16 in. cantilevers upward a distance of L = 12 ft. The pipe is subjected to a wind loading that increases from wA = 7 lb/ft at its base to wB = 11 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe?
6. The wood pole shown in the Figure 4 is supported by two cables of 4 inch diameter. The turnbuckles in the cable are tightened until the stress in the cables reaches 60,000 psi. if the working compressive stress for wood is 200 psi, determine the smallest permissible diameter of the pole. 60° FIGURE 4 60°
a.) What is the normal force distributed to Stainless Steel Solid Post 'A' (in kips)? b.)What is the normal force distributed to Red Brass Hollow Tube 'B' (in kips)? c.)What is the normal stress produced in Stainless Steel Solid Post 'A' (in psi)? d.)What is the normal stress produced in Red Brass Hollow Tube 'B' (in psi)?
Kindly quick as possible
Solution please,
A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A makes an angle of 14 degrees with respect to the horizontal axis (x-axis). a. Determine the normal stress at section A-A. b. Determine the shear stress at section A-A.
0.11
Provide correct answer Thanks for the help Determine maximum principal stress
Can someone please answer this? Thank you, in advance.
3. A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A makes an angle of 14 degrees with respect to the horizontal axis (x-axis). a. Determine the normal stress at section A-A. b. Determine the shear stress at section A-A. 300 kN A V 300 kN
A 2024-T4 aluminum tube with an outside diameter of 2.4 in. will be used to support a 30-kip load. If the axial stress in the member must be limited to 17.5 ksi, determine the wall thickness required for the tube.