The schematic of a punch and die for punching washer is shown. Determine the force F needed to punch out washers with thickness of 5mm, inside diameter of 15 mm and outside diameter of 25mm. The average shear strength of the plate is 30 MPa and average compressive stress in the puncher is 65 MPa.

Q: One shaft is in torsion as shown below. If the magnitude of shear stress at point A is 289.5 MPa,…

A: Given data: Shear stress at point A = SA = 269.5 MPa Radius of point A = rA = 40 mm = 0.04 m Shear…

Q: The 175x100x16mm angle shown in the figure connected to a gusset plate with three 25mm dia. bolts…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: The bar shown below has a constant width of 41 mm and a thickness of 16 mm. The maximum average…

A:

Q: 3. Determine the torsion on the rigid supports and the maximum shearing stress developed in each…

A:

Q: How do i determine the shear diameter of a shear pin made from 0.20C cold drawn mild steel using…

A: Given: The material is 0.20C cold drawn mild steel. And the tensile yield strength of the 0.20C cold…

Q: Puncher 20 mm o 25 mm thick Punched out F 10 20 mm 25 mm

A:

Q: For each of the structures shown in Fig.2, sketch the following: i. Free body diagrams showing the…

A: Given: FA = 300 lbf FB = 750 lbf

Q: For the screw clamp shown, a force is applied at the end of the handle 3 in from the screw…

A: Given Data:- L=3.5 in T= 3.5 F

Q: A 3/4 inch diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress of rivet…

A:

Q: Determine the vertical displacement of joint C . EA is constant

A: The vertical displacement of the joint C. FBD: The free-body diagram of the joint C is shown below.

Q: a: What is the magnitude of the maximum shear stress in MPa? b: What is the magnitude of the…

A: Consider the tensile stresses to be positive and the compressive stresses to be negative. Write the…

Q: A rigid block (neglect its weight) is to be supported by three equally spaced rods (spaced by a…

A: The schematic diagram is Free body diagram of the rigid block

Q: 1. What is the working strength of a 2'' bolt which is screwed up tightly in a packed joint when the…

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: For the direct shear example shown below, if F = 33 kN, AAB = ACD = 2146 mm2, the average shear…

A: According to the given data AAB=ACD=2146mm2 F=33kN We need to find  Shear stress in the vertical…

Q: A torque To is transmitted between two flanged shafts by means of four 20-mm bolts. diameter of the…

A: Schematic diagram of flanged shaft after considering the force F in the bo;t due to torque T

Q: A bandsaw manufacturer uses 10 inch diameter drums. If the allowable stress in the sawblade is 72…

A:

Q: Need help on all questions. Please include all units, steps to the problem and information such as…

A:

Q: A part is loaded with a combination of bending, axial, and torsion such that the following stresses…

A: Given:The material properties are .The adjusted endurance limit is .The fatigue stress concentration…

Q: If the ultimate shear strength of a steel plate is 42,000psi. What is the force necessary to punch a…

A: Write the ultimate shear strength of the steel plate.   τult=42000 psi   Write the diameter of the…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.