The roof on the building in has a slab that is 175mm thick. The beams are 300 mm. wide and have a total depth of 400 mm., the bay dimensions are 6 m. in the X direction and 6.5 m. in the Y direction, and the superimposed service dead load is 0.29 KPa. Calculate the slab factored load in KPa. Use NSCP provisions for Live Loads.

The roof on the building in has a slab that is 175mm thick. The beams are 300 mm. wide and have a total depth of 400 mm., the bay dimensions are 6 m. in the X direction and 6.5 m. in the Y direction, and the superimposed service dead load is 0.29 KPa. Calculate the slab factored load in KPa. Use NSCP provisions for Live Loads.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

STRENGTH OF MATERIALS ANS: 114 kN what is the solution to the problem?
plz, solve all the parts of this problem. Plz, use ACI Code. Reinforced Concrete Design-1 A fixed ended beam with span length of 24′ and cross-section of 15ʺ x 24ʺ is subjected to uniformly distributed load is shown in figure 1. Unform service dead load is 1k/ft and uniform service live load is 1.4 k/ft. Taking ?c = 3??? and ?y = 40???, a) Detail the reinforcement using #6 bar only, and also curtail the steel ensuring development length requirements. b) Show all your calculations in the form of neat and clean drafting.
Situation 3: A6m long fix-ended concrete beam has a width of 310 mm and an overall depth of 480 mm. The beam is reinforced with 4-28 mm diameter bars at the bottom and 2 28 mm bars on top. Steel cover measure from the center of the bar is 70 mm. f'e- 28 Mpa and fy - 415 Mpa. Total dead load including beam weight is 22 kN/m. Assuming the analysis is Doubly-reinforced beam. 7. Determine the depth of compression block in mm. 8. Determine design ultimate moment of the section if reduction factor is 0.90. 9. Determine the additional concentrated live load can carry at the midspan.
Wu-100 kN/m 6 m 4 m D Question 10 (PROBLEM 2) A three-member frame ABCD is loaded with ultimate gravity and lateral loads as shown in the figure. The compressive strength of concrete=21MPa, fy=415 MPa, beam width=300mm, beam height=600mm, main bar diameter=28mm, concrete cover=40mm, and stirrups diameter=10mm. Calculate the stress of compression reinforcement in the final section in MPa. B 4 m A mwm. Pu=115 kN
Design a simple span one-way slab to carry a uniformly distributed live load of 18 kPa The span is 34 meters (center to center of supports). Use fc 20.7 MPa and fy276 MPa. -Use NSCP 2015, conform to minimum thickness requirements. Complete solution ty..
A reinforced concrete beam that is 375 mm wide and 500mm deep must resist a service live load moment of 250 kN-m and a service dead load moment of 150 kN-m. Use f'c-21 MPa and fy=415 MPa. The effective concrete cover is 65mm (to the centroid of reinforcements). 1. Determine the area of compression steel reinforcement (If required. Answer O if not) in mm² 2. Determine the minimum number of 25 mm diameter bars to be provided to satisfy the demand ultimate moment 3. Determine the maximum number of 25 mm diameter bars to be provided to have a tension controlled section Answer 1: 2403.21 correct answer: Answer 2: 9.00 Answer 3: 8.00
A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. If the concrete has a compressive strength of 17MPa and the steel has a yield strength of 415 MPa, determine if the beam can carry a uniform distributed load of 18 kN/m dead load. The beam has a length of 5m with 40mm concrete clear cover, 10mm enclosed stirrups, and Es = 200 GPa. Use LRFD in the analysis.
Calculate the factored moment strength of the slab below. If the only dead load the slab has to handle is its own self-weight, how much service live load can the slab hold? For finding this make the moment strength you calculate equal to Mu and solve for the possible live load using a factored load equation. f'c = 3000 psi, fy = 40000 psi A A -Span for design = 12'-0"– clear #8 @ 6" 0.c. Section A-A 8"
AT-Beam has the following properties: bf = 750 mm, bw = 275 mm, d 560 mm, t = 115 mm. Concrete compressive strength fe 21 MPa and steel yield strength fy 415 MPa. T-Beam is under factored moment load of 720 kN-m. Locate the compression block under balanced condition from the extreme compression fiber.