The rigid beam is supported by a pin at A and wires BD and CE. If the load P on the beam causes the end C to be displaced 20 mm downward, determine the normal strain developed in wires CE and BD. THE RIGID BEAM IS SUPPORTED BY A PIN AT A AND WIRES BD AND CE.IF THE LOAD P ON THE BEAM CAUSES THE END C TO BE DISPLACED20mm DOWNWARD, DETERMINE THE NORMAL STRAIN DEVELOPED INWIRES CE AND BD.5m3m3m

Answered: Image /qna-images/answer/b60dcfe6-52a8-4f32-a528-5cd91602c97d.jpg

THE RIGID BEAM IS SUPPORTED BY A PIN AT A AND WIRES BD AND CE. IF THE LOAD P ON THE BEAM CAUSES THE END C TO BE DISPLACED 20mm DOWNWARD, DETERMINE THE NORMAL STRAIN DEVELOPED IN WIRES CE AND BD. LI 5m 4m 3m 3m

THE RIGID BEAM IS SUPPORTED BY A PIN AT A AND WIRES BD AND CE. IF THE LOAD P ON THE BEAM CAUSES THE END C TO BE DISPLACED 20mm DOWNWARD, DETERMINE THE NORMAL STRAIN DEVELOPED IN WIRES CE AND BD. LI 5m 4m 3m 3m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem (2) Determine the reactions at the supports A and B. Neglect the beam thickness. 500 lb 600…

Q: 13: The truss shown below has a pinned support at A and a roller support at G. Draw the influence…

Q: A non-prismatic member ij has the following stiffness matrix and the fixed-end moment vector 2.5 S40…

A: in question non prismatic member is given with stifness matrix and moment matrix and question is…

Q: 2. Fine the stress in all the members and the reactions at A of the steel frame as shown in the…

Q: Q.17 The maximum bending stress is 0039 A w/m m L P Od

Q: The Biaxial loading in column is the :case of

A: Biaxial bending of columns occurs when the loading causes bending simultaneously about both…

Q: The beam shown in Fig. is made from two boards. Draw the shear stress at (A.B.C.D) to hold the…

A: Reaction calculation For equilibrium of static (i)∑ME = 0 (ccw +ve, cw -ve) (RE x 8) - [6.5 x 4 x…

Q: The truss shown consists of wooden members. Knowing that each member has a 50 x 50 mm square…

A: Determine the maximum value of the average normal stress in (a) in member BD, (b) in member DE.

Q: A (m)– Y (N) 2 m x (N). |C 2 m A B

A: Given Data:X=482Y=82A=9

Q: 1. In the structure below, members BF and AE are connected with a pin at D. Find the minimum…

Q: Problem 4 The 7/8 in diameter pins at A and C that support the structure are in single shear. Find…

Q: PROBLEM NO. 4 Determine the absoiute maximum shear in the bridge girder due to the loading shown.…

Q: 1-20.* Member AC of the pin-connected frame ABC of Fig. P1-20 is a 2.0- in, diameter rod with an…

A: Let,Given,Diameter of member AC=2 inaxial stressσ=15000 psiforce in the member AC=axial stressc/s…

Q: (a) The axial stresses in members BC and DE (b) The shear stresses in the pin at A, assuming the pin…

A: given-cross sectional area of member=500mm2diameter of pin=20mm

Q: 8 kN/m 35° E By D 20 kN 0.4 m 0.4 m 0.4 m

Q: The beam AB is pin supported at A and supported by a cable BC. A separate cable CG is used to hold…

A: Consider the free body diagram of the beam AB:.Consider the equilibrium of horizontal forces:∑Fx =…

Q: Review: Design of simple structures 1. *1-96. Determine the required cross-sectional area of member…

Q: and frames shown.Draw the FD

Q: B 80 cm 3 kN/m -3m-4m 2m D Determine the following: 120 cm 200 cm a. Vertical reaction at point A.…

A: As per guidelines, first three sub parts have been solved.

Q: If P = 28 Ib, choose the magnitude (Ib) and type (tension or compression) of the force in member BE.…

A: Given:- a truss as shown below

Q: 5. Determine the reactions at the supports in the portal frame shown. Given: E-constant for all…

A: given Data: PL = 12kn and 30kn Need to find VA and HA

Q: EX. A steel rod 2 m hong has end fram a support structureand fa end a cross- sectional fa3 cm?. The…

Q: 3. Determine the components of reaction at the fixed support A. Neglect the thickness of the beam.…

A: Given above given figure in Q 3 we have to find the support reactions at A

Q: If P = 28 Ib, choose the magnitude (Ib) and type (tension or compression) of the force in member GF.…

Q: Practice Problem #5) Determine the reactions at the supports for the beam

A: Step 1: Given Data:A 50 kN point load at A, inclined at 30° to the horizontal.A distributed load of…

Q: AM IS SUPPORTED BY A PIN AT A AND WIRES P ON THE BEAM CAUSES THE END C TO BE DISP WARD, DETERMINE…

Q: Given the system below. It is pinned at B as shown in Fig. P-119. The pin diameter is 20 mm…

Q: Review: Design of simple structures 1. "1-96. Determine the required cross-sectional area of member…

Q: Q.17 The maximum bending stress is 0039 A w/m m L P Od

Q: A force P of magnitude 1,100 N is applied to the pedal shown satisfies a shearing stress in the pin…

A: Given data, Applied force P = 1100 N Shear Stress in the pin = 42 MPa We have to determine the…

Q: . Figure Q1 shows a steel member imposed with various loadings supported by a roller and pin at A…

A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…

Q: Q.17 The maximum bending stress is A w/m L P Ond

Q: Determine the reactions on the frame at A and D.

A: Draw the reactions at A and D as shown below Consider Moment equilibrium at D, we get Ax*0.5 =…

Q: e is hinged at rigid supports in A & E. Find the components of the Reaction at A and E and the force…

A: To find support reaction

Q: 100kN B (EA is constant) A 60KN + Determine the Force in member 4m D BD) se Force method (Consistent…

Q: The beam is supported by hinged at A & D and roller at B & C. Determine the reaction at the support.…

Q: Determine the normal force acting on the glued scarf splice in kips. b) Determine the normal stress…

Q: n, determine the maximum value o (a) in link AB, (b) in link BC.

Q: Review: Design of simple structures 1. *1-96. Determine the required cross-sectional area of member…

Q: member. (a) Dctermine the coordinates yR and Za of the point where the tensile load P must act in…

A: Please find the answer in the below attachments

Q: 1. Determine the axial stresses in members CH, AH, and CD of the loaded truss if they have a uniform…

A: The cross-sectional area of the member is 1800 mm2.Consider the figure,

Q: Q.3) A simply supported wide-flange (see figure below) beam of span length L carries a vertical…

A: Given : Section : W 10 X 30 L = 8.5 ft P = 5 kips Alpha = 26.57 degrees We are asked to determine…

Concept explainers

Pressure and Stress

Question

The rigid beam is supported by a pin at A and wires BD and CE. If the load P on the beam causes the end C to be displaced 20 mm downward, determine the normal strain developed in wires CE and BD.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

5. Determine the force in members BD and BC. Find also the force components at the pin connections at A and E. 600 N 1.50 m- 1.50 m Ras RAY 1.50 m REX REy 1.125 m 1.875 m
Determine the stress at the middle of rod BC in MPa for a given truss structure. If the diameter of rod BC is d=13 mm. P1= 12 kN ; P2= 18 kN ; a=3 (m); b=4 (m)
2. All members of the truss B shown have a cross- sectional pins have a diameter of 20mm. Determine: area of 500 mm² and all 2 m (a) The axial stresses in members BC and F E D DE (b) The shear stresses in the pin at A. assuming the pin is in double shear -2 m -2 m -2 m P = 21 kNY
The rigid element BCD is supported by a bar AB with a diameter of 25 mm and a connection at C with a diameter of 10 mm. Determine:a. The normal stress in bar AB. b. The shear stress of the bolt at C.
2. All members of the truss A B C shown have a cross- sectional area of 500 mm? and all pins have a diameter of 20mm. Determine: 2 m (a) The axial stresses in members BC and DE F E D -2 m 2 m 2 m- (b) The shear stresses in the pin at A, assuming the pin is in double shear P = 21 kN
strain free, before the lantern is hung. When the lantern is hung, it causes a 50-mm sag in the wire. Determine the Prob. 2.3-6. Determine an expression for the extensional strain e(x) at cross section x (0sxsL) of the hanging con- ical frustum in Prob. 2.2-4, and (b) determine an expression for the total elongation, e, of this hanging conical frustum in Prob. 2.2-4. The conical-frustum rod is made of material for which o = Ee, with E= const. Prob. 2.3-7. For small loads, P, the rotation of "rigid" beam AF in Fig. P2.3-7 is controlled by the stretching of rod AB. For larger loads, the beam comes into contact with the top of col- umn DE, and further resistance to rotation is shared by the rod and the column. Assume (and later show that this is a valid as- sumption) that the angle 0 through which beam AF rotates is small enough that points on the beam essentially move verti- cally, even though they actually move on circular paths about the fixed pin at C. (a) A load P is applied at end F…
Instruction: Please provide the given-required-solution and show the complete solution and the FBD. Problem: Find the forces in members HC and HG in terms of P.
Review: Design of simple structures 1. *1-96. Determine the required cross-sectional area of member BC and the diameter of the pins at A and B if the allowable normal stress is allow 3 ksi and the allowable shear stress is allow = 4 ksi. 1500 lb -2 ft -4 ft- 1500 lb B 60°
Q.17 The maximum bending stress is A - w/m L P Od
3. Determine the required diameter of the pins at A and B to the nearest 1mm if the allowable shear stress for the material is T= 300 MPa. Pin A is subjected to doble shear, whereas pin B is subjected to single shear. A 1.5 m B 1.5 m C D 30 kN 2.25m
15
Part 4a)Determine the reaction (in N) at the hinge at C.b) Determine the diameter of the pin at C in mm.c) Determine the corresponding bearing stress in the pedal at C in MPa.