The rigid bar is supported by the pin-connected rod CB that has a cross sectional area of 40 mm2 and is made from 6061-T6 aluminum (E=68.9 GPa). Determine the vertical deflection of the bar at D when the distributed load is applied.

Q: • If the hanger were not attached at B, what would be the deflection at point B • With the hanger…

A: Solution : Given data : Cross sectional area ( A ) = 3 in2                        Moment of inertia…

Q: The rigid bar is supported by the pin-connected rod CB that has a cross-sectional area of 20 mm² and…

A:

Q: Using an energy or work approach, determine the vertical deflection of point C and the deflection of…

A:

Q: Determine the Euler Buckling axial compressive load of W 12 x 72 section having a length of L=48 ft…

A: To find: The Euler Buckling load. Given: The length of the column, L = 14.63 m. Young's modulus, E =…

Q: The stress–strain diagram for a material can be approximated by the two line segments shown. If a…

A: Given data: Diameter of bar, d = 80 mm Length of the bar, L = 1.5 m = 1500 mm   Let, A = area of the…

Q: ! Criver: of 2 Assembly consist at a sibel (Es = 200 Gofa, As = 1500 mm ² ) Kod AB and GPa a brass…

A:

Q: Using Castigliano’s theorem, determine horizontal and vertical components of deflection at point C.…

A: Given dataP=1000NEA=2×106N

Q: An aluminum alloy tube with an outside diameter of 3.1 in. and a wall thickness of 0.36 in. is used…

A:

Q: Determine the critical axial buckling load for an 8 3/4 x 12 inches glue-laminated column braced at…

A: In the question , given that, E = young modulus of elasticity (1.8×106psi) dimension of column ,…

Q: A cantilever, 2.6m long, carrying a uniformly distributed load w along the entire length, is propped…

A: Given:The length of the beam is .The load at the free end is .The modulus of elasticity is .The…

Q: A 100-mm long rod has a diameter of 15 mm. If an axial tensile load of 165 kN is applied, determine…

A: Given data: L=100 mmd=15 mmF=165 kNE=200 GPa Need to determine the change in length.

Q: A square beam with a side of 7.6 cm has a density of 11,000 kg/m³ and is 2.4 m long. It is recessed…

A: The cross-section side of the square beam is a=7.6 cm. The density of the beam is ρ=11000 kg/m3. The…

Q: A column with rectangular cross section of breadth = 9mm and depth = 4mm, has its both ends are…

A:

Q: section. If AB is made up of aluminum and CD of steel, determine the required diameter of each…

A:

Q: The rigid beam is supported by a pin at C and an A-36 steel guy wire AB. Part A If the wire has a…

A:

Q: Required information Deformable rods BD and CF are attached to a rigid rod ABC as shown. Rod BD is…

A:

Q: The bar is made of aluminum alloy 2014-T6. Determine its thickness b if its width is 1.5b. Assume…

A: Given data: The width of the bar, b = 1.5b. The length of bar, L = 5 ft. The applied load, P = 800…

Q: Determine the deflection at point C and at the site of action of the load. Take Est = 200 GPa, I =…

A: The degree to which a structural member can be shifted by a significant amount of load is known as…

Q: A rectangular wooden column (E = 12 GPa) of 3 m have as dimensions shown. Determine a critical load…

A:

Q: Problem 4-13: The rigid bar is supported by the pin-connected rod CB that has a cross-sectional area…

A: Given:The cross-sectional area of the rod CB,

Q: 90 kN 70 kN (1) (2) A B C 90 kN 0.85 m 1.15 m

A: GIVEN DATA- A1=2720mm2 E1=28GPa A2=21560mm2 E2=16.5GPa

Q: A 100-mmmm long rod has a diameter of 15 mmmm. If an axial tensile load of 145 kNkN is applied,…

A:

Q: A rectangular wooden column has the cross section shown. If a = 3 in. and the column is subjected to…

A: Column fixed at its base and pinned at top  slenderness ratio, K=0.7 KLd=0.7L3=0.2333L

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.