A steel bar with a thickness 5 mm is to carry a load of 2000 N. Using the direct method, determine the deflection at each node and the average stress in each part. Divide the bar into three parts. (E=200 GPa)

Q: Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A…

A: Given: Let us consider the given data, Load, P=23 kips Temperature increased,∆T=85°F a=3.6 ftb=6.6…

Q: Consider the truss structure with a load of P= 35.4 kN applied at joint C. All the members of the…

A:

Q: The rigid beam in (Figure 1) is supported by the three suspender bars. Bars AB and EF are made of…

A:

Q: Consider a steel (Young's modulus of E=200 GPa) column hinged on both sides.Its height is and…

A: given:E=200 GPa h=1 m

Q: Determine the maximum concentrated vertical load P that can act on the top of the pillar of the…

A: The axial load which permits a member to execute lateral deflection(i.e., deflection perpendicular…

Q: B L A tube is loaded eccentrically as shown in figure. The tube has 89 mm outer diameter and 7 mm…

A: Given, Outer diameter of tube = do = 89 mm = 0.089 m Thickness of tube = t = 7 mm = 0.007 m Inner…

Q: Useful equations; o = E A 1. The steel shaft carries the axial loads as shown in the figure below.…

A: Given axial load action on stepped shaft  as shown below

Q: In the figure, the length L = 500 cm and the profile section is given, one end of which is fixed and…

A: Given data :- L = 500 m Yield stress = 300 daN/cm2  n= 0.25 Le = 2L E = 2100000 daN/cm2 Find :-…

Q: if a moment of 19 klb-ft is a tubular wall bar is shown in the figure. Determine Tmax and applied,…

A: ◆ This is the case where a thin tube is subjected to a twisting moment Mc. ◆ First, calculate the…

Q: Calculate the elastic elongations that will occur in the x y axis on the adjacent object according…

A: given stress in x direction σx=-30 MPa  (compression)stress in y direction σy=40Mpa (tensile)young…

Q: A circular plate of 80 mm radius and 6 mm thick carries a central load of 2 kN. Calculate the…

A: A circular plate with an 80 mm radius and a thickness of 6 mm supports a central load of 2 kN.When…

Q: 1: Determine the max. ultimate load (Pu) can be applied on the steel beam A36- W in Figure which is…

A: given:

Q: The length of the rectangular arm, which is fixed at both ends, is L= 9 m, and the cross section is…

A:

Q: The figure below shows the cross section of a steel rectangular tube, of uniform thickness t= 25 mm,…

A:

Q: An aluminum alloy tube with an outside diameter of 3.1 in. and a wall thickness of 0.36 in. is used…

A:

Q: 3 of 4 1.8m 1-A solid brass axial member with elastic modulus of E= 100 GPa, is loaded and supported…

A: Given : The diameter of segment of 1 and 2 is The diamter of segment 3 is The modulus of elasticity…

Q: The bar ABC is fixed at the left end and has the load P applied at C. Find the displacement c (in…

A:

Q: A solid plastic rod has a diameter of d = 44 mm and a length of L = 700 mm. An axial load of P = 22…

A:

Q: A square glass reinforced plastic plate 3 mm thick is simply supported along all the edges. The…

A: Levy's solution is a method for solving the deflection of simply supported rectangular plates…

Q: (MPa, 100 95 80 compression 70

A: for strut ABd=12mmA=π4×122A=113.097mm2For post C-d=40 mmA=π4×402A=1256.637 mm2

Q: Read the question carefully and give me right solution according to the question.. Please answer…

A:

Q: An axial load of 38.7 kN is applied to the circular member as shown. The length of the member is 15…

A: This is the very basic question of strength of material and the elongation due to axial load is the…

Q: A hollow A36 steel rod is loaded and supported as shown. Determine the stress in each side and the…

A: From the given data,  Modulus of elasticity:  E = 200 GPa (For steel rod)

Q: A= 1200 mm?. Use Strain Energy Method 35 kN - 4m B 84 kN 4m 3m

A:

Q: A steel rod having a cross-sectional area of 300 mm2 and a length of 150 m is suspended vertically…

A:

Q: A slightly tapered bar AB of solid circularcross section and length L is supported at end B…

A: Write the formula for elongation of a tapered bar under axial load. δ=4PLπdAdBE Here, E is the…

Q: The link CE (Diameter D=12mm) and DF (Diameter D=10 mm) are connected to rigid link ABCD as shown in…

A: Given data

Q: Question: A barrier gate was hit ba a car and deflected as shown in the figure. Treat the barrier…

A: For the solution refer below images.

Q: B a

A: "Since the language of the question is not so clear. If you anything else please submit the question…

Q: A steel rod having a cross - sectional area of 300 mm- and length of 15 m is suspended vertically…

A: Given:Area, A=300 mm2Length, l=15 m or 15000 mmLoad, P=30 kN or 30000 NY=200 GPa or 200×1000 MPa

Q: A column has a fixed support at both ends. If the dimensions of the column section are as given in…

A: Given- Fixed support at both ends;  L=7 m = 7000 mm E=200 GPa = 2 x 105 MPa

Q: The rigid beam AD shown carries a load W = 200 kN. It is supported by a hinge at D, a steel rod at…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.