The reaction forces applied by the unbalanced loads on the shaft to the A and B bearings,FA = 3i N and FB = 4i N. If the shaft rotates at 300 rpm, specify the magnitude of the unbalanced loads (in kg.mm) and find their angular positions. Distances are given with a= 200 mm and b = 300 mm. (Note that the angles θ1 and θ2 are not known.)

The reaction forces applied by the unbalanced loads on the shaft to the A and B bearings,FA = 3i N and FB = 4i N. If the shaft rotates at 300 rpm, specify the magnitude of the unbalanced loads (in kg.mm) and find their angular positions. Distances are given with a= 200 mm and b = 300 mm. (Note that the angles θ1 and θ2 are not known.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please and thank
Three Wheels. Three rubber wheels are mounted on axles so that they make tight contact with each other and their centers are on a line. The wheel on the far left axle is connected to a motor that rotates it at 35.0 r.p.m.; and drives the wheel in contact with it on its right which, in turn, drives the wheel on its right. The left wheel (Wheel 1) has a diameter of d₁ = 0.22 m, the middle wheel (Wheel 2) has d₂ = 0.32 m, and the far right wheel (Wheel 3) has d3 = 0.48 m. (a) If Wheel 1 rotates clockwise, in which direction does Wheel 3 rotate? (b) What is the angular speed of Wheel 3, and what is the tangential speed on its outer edge? (c) What arrangement of the wheels gives the largest tangential speed on the outer edge of the wheel in the far right position (assuming the wheel in the far left position is driven at 35.0 r.p.m)? (d) What is the largest tangential speed on the outer edge of the wheel in the far right position? (a) (b) Angular speed of Wheel 3: (c) Number Tangential speed…
You must solve all questions.
The hydraulic cylinder shown in the figure exerts a force of 3 kN directed to the right at point B and to the left at point E. Determine the magnitude of the couple M required to rotate the drum at constant speed clockwise. The picture is attached
The wheel has a mass of 100 kg and a radius of gyration of ko = 0.2 m. A motor supplies a torque M = (400 +900) N - m where is in radians, about the drive shaft at O. Initially the car is at rest when s = 0 and 0 = 0°. Neglect the mass of the attached cable and the mass of the car's wheels. (Figure 1) Figure 94°F Sunny M KI 0.3 m 1 of 1 Pro
The force F 250 N is applied to a wheel weighing 20 kg and having a radius of inertia of 150 mm as shown in the figure. This force lifts a weight B of 10 kg. Calculate the angular acceleration of the pulley and the normal acceleration of the weight B, the tension of the rope and the reaction in the bearing of the pulley.
Problem 2: Rod AB has a mass of 10-kg and a uniform cross-sectional area. The piston has a mass of 15-kg. If the flywheel rotates at a constant angular velocity of 500 rev/min, determine the forces on A and B when 8 = 60°. Use a Vector Approach, show all your work. 150 mm, 750mm
The system below shows a system consisting of 4 masses that are turn. If R₁= R₂ = R3 = R4 = RA = RB = 10, determine the MA and MB placed in field A and field B.
3.For the slider-crank mechanism shown in the following figure, link 1 rotates counter clockwise. AB=20mm, BC=50mm, e=15mm. Calculate the minimal and maximal pressure angle, amin and amax. 4 3 А 2 1 В
β=θ+γ =60+20 =80Can u explain why the above equation is used in determining the angle of wrap and why does in all 3 pulleys u used same β
Mechanical engineering
Question 1 (Type B) Determine the couple moment acting on the circular wheel. The wheel has a diameter of 20 inches. The steering column (OC) is in the yz plane and the wheel is perpendicular to OC. Express your answer as a Cartesian vector and calculate its magnitude. F, = 55 lb A 30° ►y F3 = 55 lb