A shaft carries four masses A, B, C and D with a a magnitude of 200kg, 300kg, 400 kg and 200 kg respectively and revolving at radii 80mm, 70mm, 60mm and 80mm in planes measured from A at 300mm, 400mm and 700mm. The angles between the cranks measured counter clockwise are A to B 450, B to C 700 and C o D 1200. The balancing masses are to be placed in planes X and Y. Distance between planes A and X is 100mm, between X and Y is 400mm and between Y and D is 200mm. If the balancing masses revolve at radius of 100mm find their magnitude and angular position

Q: Which method of tolerancing does not exist?   a)Limit tolerance b)Triolateral tolerance c)Bilateral…

A: There are basically three types of tolerances exist in the metrology  Limit tolerance Bilateral…

Q: 5. Consider the disk with a rectangular cutout shown in the figure below. The disk has the…

A: Given: The thickness of the disc, t = 3 m The density of the disc, d = 4000 kg/m3

Q: completely balanced

A: Plane mass(kg) radius(m) centri force÷ω2 (kg.m) length(n) couple÷ω2 (kg.m2) A mA .18 .18mA -y…

Q: Structure ABCD is rigid and is built-in at point A. Point A is at the origin of the coordinate…

A: Since CD is perpendicular to AB, the dot product of the vectors AB and CD should be zero. The…

Q: A wheel has a string of length 4 m wrapped round its shaft. The string is pulled with a constant…

A: Given, Length of the string L = 4 m Force F = 150 N n = 3 rev/s Moment of inertia of the wheel I =?…

Q: The machine element shown is fabricated from steel. The density of steel is 7850 kg/m³. Determine…

A: Given, a=35 mm,b=60 mm,c=20 mm,d=40 mm,e=70 mm,Density of steel, ρ=7850 kg/m2

Q: The figure below gives the moment of inertia Io for a point mass rotating about point O. As a…

A:

Q: wheel with a mass of 20 kg and a radius of inertia of 300mm, moves under the influence of a torque…

A:

Q: 5. A person pulls on a rope with a force of 100 lbs as shown below. What is the moment about point A…

A:

Q: There is a pirate ship in the harbor which features a large, cast iron wheel that is used to steer…

A: External torque  Tpush=33.7Nmresisting torque Tre=10Nmso the net torque acting on the wheel…

Q: You are attempting to rotate a heavy table about the base of one leg at O. Assuming the moment about…

A:

Q: Examples: Moments of inertia of the pendulum about an axis 1) passing through point O, and 2) mass…

A:

Q: Two gears with fixed pins at their (geometric, mass) centers (C₁, C₂) are in mesh as shown. The gear…

A:

Q: 600 mm C 360mm

A:

Q: Locate the center of mass by finding the distances x and y. Answers: X = y= i X 1075 mm ¡y mm mm 310…

A:

Q: Find the center of mass (x̄, ȳ, z̄) of the object shown, given:   L1 = 20 mm,   L2 = 34 mm,   L3 =…

A: The given figure converted into two cuboids as: C1: (L6,L5,(L2+L3)C2: (L1,L2,L4)L1=20 mmL2=34…

Q: The following masses m; are located at the given points P₁: m₁ = 6, P₁(1, -2) m₂ = 5, P₂(3, 4) m3 =…

A:

Q: The bar below is 8 meters long and has a 37° 'F=500N negligible mass Three external forces act on it…

A:

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.