The pressur of the air in the figure is 10.7 kPa, and the manometer fluid is of unknown specific gravity (S.G.). Determine (S.G.) for the deflections shown. 10.7 kPa Ps 4 cm 8 cm DAU 7 cm Air Open to atmosphere Heptane 0.81 Mercury

The pressur of the air in the figure is 10.7 kPa, and the manometer fluid is of unknown specific gravity (S.G.). Determine (S.G.) for the deflections shown. 10.7 kPa Ps 4 cm 8 cm DAU 7 cm Air Open to atmosphere Heptane 0.81 Mercury

Name: i need clear ans and solve very very fast in 20 min and thank you | ᴅʏ
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: i need clear ans and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛ The pressur of the air in the figure is10.7 kPa, and the manometer fluid is ofunknown specific gravity (S.G.). Determine(S.G.) for the deflections shown.10.7 kPaAirHeptane

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PLEASE ANSWER THIS USING YOUR OWN ANSWERS. DO NOT COPY ON INTERNET. IF YOU SEE THIS QUESTION AGAIN, DO NOT ANSWER. IF YOU ANSWER THIS IN TYPEWRITTEN, COMPLETE, CORRECT, AND IN ORIGINAL WAY, I WILL UPVOTE. THANK YOU!
The process defined by the figure is characterized by: O Machining tolerance class up to IT8 O Greater material removal O Excellent surface finish
Solve fast please
i need clear ans and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛
Task 4 Here students need to calculate (a) The cutting speed (b) Turning time (c) Amount of material removed. For a specimen as shown below, if spindle rotates at N = 360 rpm, number of pass = 03, feed rate= 0.2mm/rev, if density of material=7.85× 10-6 Kg/mm³. Appendix Volume for Cylinder = rr?h Volume of frustum= nh (a?+b²+ab)/3 radii 'a' & b' height(Length) 'h'. b-a Taper angle : = tan20 h TDN Cutting speed:V : meters/min 1000 Where: V = Cutting speed in Meter/minute. T= 3.14 D = Diameter of work piece in mm N = rpm Cutting Time Length of the job to be turned NO.of cuts Time to turn mins. Feed/Rev rpm Amount of Material Removed = Original Mass – Machined Mass Original Size of Component 380 mm Machined Component 80 mm 100 mm 120 mm 6 20mm + 25mm + 40mm + 25mm 030mm
Solve it quickly please now
Q1. The part shown below will be turned in two machining steps. In the first step a length of (50 + 50) = 100 mm will be reduced from Ø100 mm to Ø80 mm and in the second step a length of 50 mm will be reduced from Ø80 mm to Ø60 mm. Calculate the required total machining time T with the following cutting conditions: Cutting speed V=80 m/min, Feed is f=0.8 mm/rev, Depth of cut 3 mm per pass. Ø100 Ø80 Ø60 50 50
solve question 6
i need clear ans and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛
Parvinbhai