The present pumping rate of North Slope crude oil through the Alaska Pipeline is about 600,000 barrels per day (1 barrel = 0.159 m3), pipe diameter is 48 inches. What would be the maximum rate if the flow were constrained to be transitional? Assume that Alaskan crude oil fits Fig. A.1 of the Appendix at 60°C. From Fig. A.1 for crude at 60°C, p = 0.86(1000) = 860 kg/m3 and u = 0.0040 kg/m-s. Take note that the maximum Turbulent Reynolds number is about 4000. Select one: O a. 6890 barrels b. 6897 barrels O c. 9680 barrels O d. 9687 barrels

The present pumping rate of North Slope crude oil through the Alaska Pipeline is about 600,000 barrels per day (1 barrel = 0.159 m3), pipe diameter is 48 inches. What would be the maximum rate if the flow were constrained to be transitional? Assume that Alaskan crude oil fits Fig. A.1 of the Appendix at 60°C. From Fig. A.1 for crude at 60°C, p = 0.86(1000) = 860 kg/m3 and u = 0.0040 kg/m-s. Take note that the maximum Turbulent Reynolds number is about 4000. Select one: O a. 6890 barrels b. 6897 barrels O c. 9680 barrels O d. 9687 barrels

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In mechanical fluid
The critical Reynolds number makes a distinction between laminar and turbulent flow regimes of objects immersed in a fluid, as shown in the table below: Type of flow Re critical Pipeline flow 2300 Flow over smooth plate 5,0x10^5 Flow over smooth sphere 4,0x10^5 Considering that an airplane takes off with a speed of 260km/h and that rhoAR = 1.29kg/m^3, miAR= 1.81*10^-5 kg/(m*s), what is the length of the boundary layer over the wings where does the flow become turbulent?
Helium (Table A.4) enters a 5-cm-diameter pipe at p1 =550 kPa, V1 = 312 m/s, and T1 = 40 °C. The friction factoris 0.025. If the flow is choked, determine (a) the length ofthe duct and (b) the exit pressure.
Carbon Dioxide (CO₂) gas flows steadily in a convergent nozzle. At section 1, flow conditions are T₁ = 400K, P₁ = 500 kPa and M₁ = 0.65. The mass flow rate at exit section (not the same as section 1), is 1.742 kg/sec. The area of cross section A₁ is (in m²), Group of answer choices 0.0007 0.0010 0.0013 0.0016 0.0019
Calculate the hourly energy cost for pumping riverwater at 288.706K, from a river to a hilltop, through a 0.458-ft ID pipeline at an average velocity of 8.1818 mi/hr (mph). The pipeline is 0.8523 miles long and discharges into the atmosphere at a level 0.5682 miles above the level of water in the river. The pump is 70 percent efficient and local energy cost is 7 cents per KWH. Assume friction losses inside the pump to be 1.0779 kJ/kg.
SAE 10W30 oil at 20oC flows from a tank into a 2 cm-diameter tube 40 cm long. The flow rate is 1.1 m3/hr. Is the entrance length region a significant part of this tube flow? Hint : The flow rate is 1.1 m3/hr.
Q2: By using the General flow equation: Rew d 0.5 (P? - GT;LZ Q = 38.77F D².5 Approve that, for two parallel gas pipelines (1- BCE & 2-BDE ) as shown in the figure below, the equivalent pipe diameter for both pipelines can be determined by the following equation: 1/5 K. 1+ const1 K D, = D1 const1 where A E K2 (D 5 La constl =
In the design of a 500m long water pipeline it is proposed to keep head loss, hf, less than 6m for a flow of 0.50 m's1. The pipeline must also be able to withstand water hammer pressures under rapid valve closure condition at the discharge end. Two types of pipes- PVC and steel - each 50 cm in diameter are available. Which pipe will you recommend? 1. The Darcy friction coefficient, 2, can be estimated from Figure 1. The value of the roughness height for steel pipe is 0.00015m, while the PVC pipe can be considered hydraulically smooth. The thickness of each pipe is 1 cm and the Modulus of Elasticity, E, for steel is 200x10° Nm2 and for PVC is 1.7×10®N%?. The Bulk Modulus of Elasticity, K, for water is 2x10°Nm2. The working pressures for the steel and PVC pipes are 2 MPa and 1 MPa respectively. 0,1 0,09|Laminar flow f IN aica Transition 0,08 Laminar Critica! flow Complete turbulence, rough pipes Zone 20ne 0,05 0.07 0,04 0,06 0,03 0,05 0,02 0,015 Lio 0,04 0,01 0.008 Re, 0,006 0,03 0,004…
A SAE 30 oil at 38°C flows through a 0.01-m diameter, with a 4-m long pipe which is inclined at a 31-degree angle at a flow rate of 0.18 L/s (1000 L = 1 m3). Estimate the pressure loss (in kPa) across the pipe.
(2) It is desired to deliver 60 m'/hr of water at 20°C through horizontal asphalted cast iron pipe. Estimate the pipe diameter d that will cause the pressure drop to be exactly 40 kPa per 100 m of pipe length. Take water density p Solve this problem iteratively using either Moody chart or the Colebrook equation. 998 kg/m and dynamic viscosity µ = 0.001 kg/(m.s).
Show work for both subparts as it is a single problem.