The post is made of a material with modulus of elasticity equals 13(10") KN/m and has a diameter of 80 mm. If it is subjected to the load of 20 KN and the soil provides a frictional resistance that is uniformly distributed along its sides of w =5 KN/m determine the force F at its bottom needed for equilibrium. Also, what is the displacement of the top of the post A with respect to its bottom B? Neglect the weight of the post. %3D 20 kN

The post is made of a material with modulus of elasticity equals 13(10") KN/m and has a diameter of 80 mm. If it is subjected to the load of 20 KN and the soil provides a frictional resistance that is uniformly distributed along its sides of w =5 KN/m determine the force F at its bottom needed for equilibrium. Also, what is the displacement of the top of the post A with respect to its bottom B? Neglect the weight of the post. %3D 20 kN

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.11P

See similar textbooks

Related questions

Q: ubjected to an evented by the

Q: a. Determine the largest distributed load value in lb/ft. b. Determine the point of inflection from…

A: Shear force for Uniformly Distributed Load(UDL) is a Uniformly Varying Line(i.e., sloped line) In…

Q: A steel girder of 6m length acting as a beam carries a uniformly distributed load w N/m run…

Q: х- ахis IS

Q: A simply supported wood beam with overhang is subjected to uniformly distributed load q. 1m- 250 mm…

A: To find the maximum permissible value of q

Q: an adequate lateral supports. The allowable bending stress is 11.8 MPa, allowable deflection of…

Q: A steel wire 30 ft long, hanging vertically, supports a load of 500 lb. Neglecting the weight of the…

Q: Aroadway sign weighs 6 kN and is supported by a structural pipe that has an outside diameter of 245…

Q: mm rectangles arranged as shown. A. Determine the maximum value of w without exceeding the…

A: solution of above problem is below:

Q: A wooden beam carries the loading shown. Determine the smallest allowable width b of the beam if the…

Q: SITUATION 3: A steel pipe of 300-mm outer diameter and 15-mm thickness is used as a column to carry…

Q: A cantilever of circular solid cross section is fixed at one end and carries a concentrated load P…

A: step 1-

Q: 1. Consider Figure FE 1. In reference to the figure, prepare a concise explanation of the…

A: For the prediction of settlements of buildings, bridges, embankments, and other structures…

Q: beam has a uniform dead load and live load has a fixed support at both ends. If the beam properties…

Q: What is the value of the shear stress at the neutral axis in a rectangular section of base b, height…

Q: 2. An aluminum strut 2 m long has a rectangular section 20 mm by 50 mm. A bolt through each end…

Q: Defferentiate the following terms; 1.Resilience and proof resilience 2.proof resilience and modulus…

Q: Two plates each 25 mm thick and 130 mm wide are fastened by three 20 mm diameter rivets. Assume that…

A: The tensile stress is defined as the ratio of the applied load in the direction of increasing length…

Q: 1. *A propped cantilever has a 2m overhang. The beam has a load of 2W applied half way between the…

Q: The beam shown has a rectangular cross section with a depth h = 240 mm. Determine the width b of the…

A: It is required to find the width of the beam.

Q: 2.4 diameter steel molding

Q: 420mm 850 mm b = 039 mm M = 6.5 KN.m E = 186 KN.m 1. Calculate the max. tensile and compressive…

Q: 1. Determine the following: a. Determine the moment of inertia of the section about its neutral…

Q: A steel wire 10Om long hanging vertically supports a tensile load of 2000N. Neglecting the weight of…

A: Stress is the strength of the material per unit area of the cross-section. Also called as the…

Q: Determine the Adjusted Unit Compressive Stress for a rectangular column with dimension of 200 mm x…

Q: 1. A steel circular bar (the yield stress oy = 350 MPa) with diameter d = 60mm is acted upon by…

Q: AP Cable sling 32° 32° Clevis 2.0 m

Q: Consider a fillet section subjected to a tensile force F. Knowing that the fillet section has a…

A: I am solving only three sub parts as per Bartleby guidelines.

Q: 1. The column has the cross-sectional area of 12000 mm². It is subjected to an axial force of 50 KN.…

A: step 1-

Q: 1000 N/m Given: A cantilever beam has loading and cross section as shown. The allowable stress is 64…

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

The post is made of a material with modulus of elasticity equals 13(10") KN/m and has a diameter of 80 mm. If it is subjected to
the load of 20 KN and the soil provides a frictional resistance that is uniformly distributed along its sides of w = 5 KN/m determine
the force F at its bottom needed for equilibrium. Also, what is the displacement of the top of the post A with respect to its bottom
B? Neglect the weight of the post.
%3D
20 kN
2 m
B.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A wooden beam carries the loading shown. Determine the smallest allowable width b of the beam if the working stress in bending is 10 MPa. 2 kN/m 5 kN yox 200 mm B 1.0 m 2m 1.0 m C
60 mm 150 mm 60 mm 300 mm 600 III 60 mm 150 m
What is the value of the shear stress at the neutral axis in a rectangular section of base b, height h and subjected to the shear force F? 1.3F/b O 2. (3F)/(2bh) O 3. F/2
A short column has a rectangular cross-section with sides in the ratio 1:2. Determine the minimum length of the short dimension (B) in mm of the column section to prevent yielding, if the column carries a 537 kN axial load and the failure stress of the material of the column is 371 N/mm². P KN B 2B *Hint: First identify the minimum area of the cross-section B=
Shear Stress H.W W= lo EN/m 5m T= ?
Defferentiate the following terms; 1.Resilience and proof resilience 2.proof resilience and modulus of resilience B)A solid beam ABC circular in section has varying sections.portion AB is 6m in length and diameter of 250mm while portion BC is 2m in length and section diameter of 100mm.The beam is subjected to a sudden tensile load.if the maximum stress induced is 400MN/m^2.Determine the strain energy stored in the beam.Take E=200GN/m^2
Determine the maximum compressive stress in the loaded beam shown. 50 kN 10 kN/m BA 5 m 5 m 5 m 5 m O 1450.55 MPa O 2019.75 MPa O 750 MPa О 250 МPа O 45.44 MPa O 673.25 MPa O 785.44 MPa O 36.81 MPa 180.93 МPа O 261.81 MPa Next
2. An aluminum strut 2 m long has a rectangular section 20 mm by 50 mm. A bolt through each end secures the strut so that it acts as a hinged column about an axis perpendicular to the 50 mm dimension and as a fixed ended column about an axis perpendicular to the 20 mm dimension. Determine the safe central load, using a factor of safety of 2.5 and E= 70 GPa. Ans. P= 9.212 kN
A round vertical steel column 500 mm in outside diameter and a wall thickness of 10mm is reinforced with four reinforcing bars 3 cm in diameter. It is filled with concrete and supports a load of 800 kN. Bearing plates are placed on top and bottom of the 1.5 m high column to assure equal deformation of the steel and concrete. Find the stress in each material and the change in height of the column. [Ec = 14 000 MPa, Es=200 GPa assume both column and steel re-bar are same type of steel]
The solid shaft is subjected to the distributed andconcentrated torsional loadings shown. Determine therequired diameter d of the shaft if the allowable shear stressfor the material is torqueallow = 60 MPa.
A cantilever of circular solid cross section is fixed at one end and carries a concentrated load P at the free end. The diameter at the free end is 200mm and increases uniformly to 400mm at the fixed end over a length of 2 m. At what distance from the free end will the bending stress in the cantilever be maximum? Proceed to calculate the value of maximum bending stress if the concentrated load P = 30 kN. I need answer ASAP. Thank you!
Help me