A simply supported wood beam with overhang is subjected to uniformly distributed load q. 1m- 250 mm 200 mm Ⓡ The beam has a rectangular cross section with width b = 200 mm and height h = 250 mm. Determine the maximum permissible value q if the allowable bending stress is all 12.0 MPa, and the allowable shear stress is Tall = 1.25 MPa. (Enter the magnitude in kN/m.) kN/m

A simply supported wood beam with overhang is subjected to uniformly distributed load q. 1m- 250 mm 200 mm Ⓡ The beam has a rectangular cross section with width b = 200 mm and height h = 250 mm. Determine the maximum permissible value q if the allowable bending stress is all 12.0 MPa, and the allowable shear stress is Tall = 1.25 MPa. (Enter the magnitude in kN/m.) kN/m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

We have simply supported two-way slap as shown below. If the density of concrete is 2450 kg/m3, calculate the maximum bending moment in kN.m at beam A due to the un-factored self weight of the concrete slab. ... 7 m 7 m 5m Beam A
HW: For the cracked beam of details shown in Figure, check the bending stress. mm WD-10 kN/m WL= 12 kN/m working stress Design method 5 m 3020mm 450 mm Q+ 170 mm 250 mm
An axial load P is supported by a short steel column, which has a cross-sectional area of 10500 mm2. If the average normal stress in the steel column must not exceed 140 MPa, determine the minimum required dimension “a” so that the bearing stress between the base plate and the concrete slab does not exceed 11 MPa.
A pre-tensioned rectangular beam 150mm wide and 300 mm depth is prestressed with three straight tendons each having a cross-sectional area of 50 mm? to an initial stress of 1200 N/mm?. The tendons are located at 100 mm from the soffit of the beam. If the modular ratio is 6 the loss of prestressing force (in kN up to one decimal place) due to the elastic deformation of concrete is
1. The overhang beam has a composite cross section as given below. Determine the maximum compressive and tensile stresses at the beam cross section due to the forces acting on the beam. Draw the stress distribution along the height of the cross stresses. (E=5000 MPa) 24 kN 18 kN/m 9 cm C x 30cm AB A 6.00 m 9cm +9㎝ +9㎝ 9cmt cm -1.50m
3. A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A makes an angle of 14 degrees with respect to the horizontal axis (x-axis). a. Determine the normal stress at section A-A. b. Determine the shear stress at section A-A. 300 kN A V 300 kN
Q.3.L
Solve this question as soon as I upvote solution
Beam Number 1 R₁ 25 kN-m 1m 1m 3m 10 kN/m R₂ 2 m
1000 N/m Given: A cantilever beam has loading and cross section as shown. The allowable stress is 64 MPa. 150 mm Determine: the minimum width for the beam 6 m b
A reinforced concrete beam experiences a load as shown. It has a base of 350 mm, and an effective depth of 600 mm, with 4 – 25 mm diameter rebars. The concrete has a compressive strength of 27.6 MPa, Determine the maximum distributed load that the beam can carry. Assume that the allowable stress in steel is 167 MPa (instead of 160 MPa). w 1.5 m 10 kN 1.5 m 5 m
A rectangular reinforced concrete beam has a width of 300 mm and an effective depth of 700 mm. It is subjected to a nominal moment of 550 kN-m. If fc = 28 MPa, fy = 280 MPa, and Es = 200 GPa. a. Determine the balance steel ratio in percent; b. Solve for the depth of the equivalent rectangular stress block; c. Check whether the beam is tension-controlled, compression-controlled, or within the transition region and determine the value of the strength reduction factor, ; d.Solve for the ultimate moment capacity of the beam.