The pin-jointed frame work in the figure If a vertical D F. concentrated load of 800KN (downward) and horizontal force of 1200KN (to the right) are applied at Point C. a. Determine the vertical reaction in kN at the 4m hinge (point B). b. Determine the horizontal reaction in kN at the E hinge (point B). c. Determine the vertical reaction in kN at the roller (point A). 3m 3m d. Determine forces in member AB. (in kN) and identify if it is tension (T) or compression (C) e. Determine forces in member BD. (in kN) and identify if it is tension (T) or compression (C)

The pin-jointed frame work in the figure If a vertical D F. concentrated load of 800KN (downward) and horizontal force of 1200KN (to the right) are applied at Point C. a. Determine the vertical reaction in kN at the 4m hinge (point B). b. Determine the horizontal reaction in kN at the E hinge (point B). c. Determine the vertical reaction in kN at the roller (point A). 3m 3m d. Determine forces in member AB. (in kN) and identify if it is tension (T) or compression (C) e. Determine forces in member BD. (in kN) and identify if it is tension (T) or compression (C)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What is the maximum positive moment for the beam shown? Use the method of consistent deformations. Select the reaction at the roller support to be the redundent 75 kN m 120 kN B 6 m 6m El = constant O a 107 4 k ft Ob. 670.8 k.ft O C 252.7 k-ft O d. 303.0 k ft
9-3. Determine the reactions at the supports, then draw the moment diagram. The moment of inertia for each segment is shown in the figure. Assume A and C are rollers and B is a pin. Take E = 200 GPa. 6. B. 40 kN 20 kN 20 kN IAB = 120(10°) mmLD IBC = 90(10°) mm %3D -3 m 3 m -3 m- -4 m- 4 m- iq s zi 8 omua2A 2noiloco högqua on nimmote Jns Prob. 9-3olloT o bms A brs
The ABC rigid bar is suspended by the BD rigid bar and by an A pin that connects it to the other ADE rigid bar. If the overhang load at point C is equal to 12kN, calculate the force on the BD bar and the reactions FA = √??2 + ??2, on pin A and the reaction FE roller located at point E. Disregard the weights of all the bars.
What is the maximum positive moment for the beam shown? Use the method of consistent deformations. Select the reaction at the roller support to be the redundant. 120 kN 75 kN - m C B 6 m 6 m El = constant a. 303.0 k-ft b. 670.8 k-ft c. 107.4 k-ft d. 252.7 k-ft O O
A snow load of 3 kPa rests on a roof whose trusses are spaced 3m on center. Find: 1. Determine the magnitude of the equivalent concentrated load acting at point C.2. Determine the force at member BF. Specify if tension or compression.3. Determine the reaction at E
Question 1 Consider the pipe segment AB that lies in the az-plane and is bent in a circular form with radius 4 m. The pipe is supported at A by an unknown support and at B with a cable BC. B' A50 4 m If the support at A can resist a maximum cou- ple moment of 1 650 Nm, determine the small- est force F that will cause the support to fail. F 6 m D 6 m
The beam AB has a moment of inertia I = 800(106)mm4, and rests on the smooth supports at its ends. A 50 mm in diameter post CD is placed at the center of the beam. If the temperature of the rod is increased by 100 °C, determine the force developed in the rod. The beam and rod are both made of steel for which E = 200 GPa and α = 11.7(10-6) /°C.
Q2. Member ABC is supported by two fixed supports at points A and C. The member has heights of 100mm at points A and C whereas the height is 600mm at point B. A point torque of 10KN.m is applied Im away from the point A. Determine the reactions at supports A and C. Write vour results in the box below. Use G-100GPA. B A T= 10 kN.m 100 mm 600 mm 1 m 1 m 2 m
4. Determine the reactions at support A and B. Assume A is a roller and B is a pin 20 kN 4m 6m 30 kN C 8m 40 kN D B 12 kN/m 7m
600 lb 450 lb E -3 ft- B 30° -3 ft Prob. 1 2. The truss is shown in the figure. (a) Determine the reaction forces at A and E. The roller at A is supported at a horizontal surface. (b) Is the structure symmetric? (c) Determine forces in all members and show the forces on the truss.
Rigid bar ABCD is pinned at C and supported by bars (1) and (2) at A and D, respectively. Bar (1) is aluminum and bar (2) is bronze. A concentrated load P = 80 kN is applied to the rigid bar at B. Compute the normal stress in each bar and the downward deflection of the rigid bar at A.