The pictorial representation below gives the relevant diameters of a 2ml syringe. A nurse uses the syringe to inject medicine into a patient with a blood pressure of 140/100. (a) How much force must he exert on the plunger with his thumb? (b) If the syringe is emptied in 2 seconds, what is the speed of flow of the medicine through the needle? 0.25mm 6.0 mm +

The pictorial representation below gives the relevant diameters of a 2ml syringe. A nurse uses the syringe to inject medicine into a patient with a blood pressure of 140/100. (a) How much force must he exert on the plunger with his thumb? (b) If the syringe is emptied in 2 seconds, what is the speed of flow of the medicine through the needle? 0.25mm 6.0 mm +

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

show your solution asapp
Solve with the correct units 6. A square block weighing 1.1 kN and 250 mm on an edge slides down in a 20° inclineon a film of oil 6μm thick. Assuming a linear velocity profile in the oil, what is the terminal speed of the block?The viscosity of the oils is 7 mPa . s.
12:45 M O What would be the maximum weight W of the block, shown in the following figure, so that the tension developed in any cable does not exceed 1000 N: A |30° II
You are being asked to determine the heights in tubes B and C (relative to z=0) given the following information: The specific weight of Air is Pair = 11.9N/m3 The specific weight of glycerine is Paiye = 12355N/m3 The specific weight of gasoline is Pgas = 6677N/m3 The gauge pressure at A is Pa = 1.6kPa The height of the tank of air is a = 1.7m The height of the tank of gasoline is y = 1.6m The height of the tank of glyercin is k = 0.95m A в с xm Air y m Gasoline k m Glycerin z = 0 As a HINT, you do not need to know the specific elevations of the tubes B and C entering their respective fluids, but you do need to account for this. Input the height the fluid rises in B to 2 decimal places here: (in metres) Input the height the fluid rises in C to 2 decimal places here: (in metres)
valg, (21535mm 1.15 The pressure difference, Ap, across a partial blockage in an artery (called a stenosis) is approximated by the equation μV Ap - K. 4 + K.(A-1) pv² = K₂ A s.r to zogy nish190 32\V as bonb dignol a 3 basiy noft where V is the blood velocity, u the blood viscosity (FL-2T), p the blood density (ML), D the artery diameter, Ao the area of the unobstructed artery, and A, the area of the stenosis. Determine the dimensions of the constants K, and K. Would this equation be valid in any system of units?
Give some examples of Other Pressure Measurement Devices?
Write T as an answer if the statement is true and F as an answer if the statement is wrong. If your answer is F, then correct the statement Example: Q1- Sinop is a southern city located at Anatolia. A typical answer 1- F: Sinop is a northern city located at Anatolia. Question2-1 Thermal hot wire anemometers measure the temperature of the flow, and they are very small devices which do not disturb the flow significantly. Question2-2 Using a Laser Doppler velocimetry, one can measure the velocity information at a cross section instantaneously. Question2-3 An obstruction flow meter can be used to measure the velocity profile around a car in a wind tunnel. Question2-4 The exact value of the discharge parameter of an orifice meter should be supplied by the producer because it has a design based value.
resolve both, show all steps and solutions
3. Determine: (a) The equivalent length in meters of pipe that would have the same loss as a fully open angle valve placed in a 150 mm commercial steel pipe, (b) The output power by a 70% efficient turbine if the energy delivered by the water to the turbine is 58 N.m/N and the rate of flow is 115 L/min. (c) The volume flow rate of the fluid [sg = 1.32] as it escapes through a 30mm hole in the side of a tank down 4m from the top of the fluid's surface when the coefficient of velocity is 0.90 and the coefficient of area is 0.82. (d) The pressure drop across a 45 degree standard elbow in a 75 mm commercial steel pipe when oil sg = 0.85 is flowing at 800L/min
At one point in a pipeline the water's speed is 3.00 m/sand the gauge pressure is 5.00×10^4 Pa a) Find the gauge pressure at a second point in the line, 11.0 mm lower than the first, if the pipe diameter at the second point is twice that at the first. Express your answer in kilopascals.
Y- young’s modulus
PLEASE ANSWER THEM ALL FOR AN UPVOTE. THANK YOU. Given: Pi constant to be used: 3.14159 Capillary tube: radius = 0.02 cm; length = 9 cm; pressure = 0.7 mmHg Liquid sample: density = 4 ml; time of flow = 4.5 seconds Ans. the ff questions. •What is the pressure in MKS unit? •What is the pressure in CGS unit? •What is the viscosity of the liquid? • If the weight was given as 8.5 grams, what will be the density of the liquid? •What is the kinematic viscosity of the liquid? •What is the fluidity of the liquid?