The pendulum consists of a 4-kg circular plate and a 3-kg slender rod (Eigure 1) Figure 2 m ון < 1 of 1 > ▾ Part A Determine the radius of gyration of the pendulum about an axis perpendicular to the page and passing through point O Express your answer to three significant figures and include the appropriate units. LO ko 2.10 μA 3 Provide Feedback m SMAR Submit Previous Answers Request Answer ? * Incorrect; Try Again; 3 attempts remaining

Q: where did 144 come from

A:

Q: 5- HB Pencil is used to fill the sheet table. O True O False 2- Choose the correct answer: Oa- A3…

A: 5. HB pencils are used in a sheet because it gives dark mark to identify the sheet table so the…

Q: Cold rolling is a process that can reduce the thickness of a piece of metal material and introduce…

A: Solution; Given Data: Cold rolling is a process that can reduce the thickness of a piece of metal…

Q: In which of the following casting process, the melting pot is an integral part of the machine. * O…

A:

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: With reference to the drawing callout in figure 5 below, which part(s) would 'pass' or 'fail' along…

A: Data given-  Dimensions of standard size  0.25±0.01 So tolerance is equal to 0.02  And the upper…

Q: Describe thrust angle.

A: Introduction  The thrust angle is basically used as a major angle for alignment of the rear and…

Q: solve parts 4 and 5 please

A: To draw Mohr circle and to show the orientation of the element of maximum in plane shear stress

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

A:

Q: Q.2 A cantilever beam of length / = 5 m, flexural rigidity El in MPa, and mass m = 1950 kg carries…

A:

Q: Choose the correct word to complete the -5 following sentence: The fault was.......... .None of the…

A: Correct answer: (c) undetected

Q: Answer in 4-10

A: Given: →h1=3387.31 KJ/Kg→h2'=3074.5 KJ/Kg→h3=3457.04 KJ/Kg→h4'=3109.82 KJ/Kg→h5'=2384.82…

Q: I need this part answered according to the disrections provided in the image.

A: Match each of the following terms to the phrase that describes it

Q: ENTIRE ANSWER IS WRONG

A: Initial velocityFinal velocityInitial angleFinal angleWeight of the basketball

Q: For figure (4): The ring is subjected to two forces (F, and F2). Suppose that the resultant force…

A: Given data:

Q: Question 1 Figure Q1a shows two cables attached to a half-ring anchor point as shown in Figure Q1a.…

A: 1-Use resultant formula of 2 force to solve first problem, 2- use equilibrium equilibrium to solve…

Q: I need help answering this Review Activity

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: Please show all the steps, thanks

A:

Q: With reference to the drawing callout in Figure 4 below, which part(s) would 'pass' or 'fail'…

A:

Q: Q2/ Fill in the blanks with suitable phrases or terms:- 1- The typical composition of austenitic…

A: 1. The typical composition of austenitic stainless steel is            Note :- you have posted…

Q: thế časting part whose perspective pictures are given below, take into account the surface of the…

A: COVE DESIGN

Q: Incorrect please resolve both parta

A: To calculate the surface temperature of the tank when it is passed through water and to calculate…

Q: why is the length of the wire use in finding the centripetal force instead of the radius?

A:

Q: Write the Column Formulas?

A: Types Critical load Both ends hinged π2EIl2 one end hinged other end fixed 2π2EIl2 both ends…

Q: Name at least two units that you use every day.

A: Most of the time in the day to day life there are many duties which have to be done daily y u. Some…

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.