The outer radius of a concentric spherical electrode system is r2= 25 cm = constant. The systemis dimensioned with regard to the optimum breakdown case. There is an insulator gas in betweenspheres with a breakdown strength of E, = 25 kV/cm (the relative dielectric constant of gases isEr = 1).a. Determine the capacitance and maximum voltage that can be applied for this system.b. Determine maximum and minimum electric field strength if the applied voltage is U =100 kV.Determine the actual electrode separation, d; effective electrode separation, a andutilization factor, n for this electrode system (ɛo = 8.854 × 10-12 F/m).с.

Given Eb = 25 kV r2= 25 cm εr = 1

The outer radius of a concentric spherical electrode system is r, = 25 cm = constant. The system is dimensioned with regard to the optimum breakdown case. There is an insulator gas in between spheres with a breakdown strength of E, Er = 1). 25 kV/cm (the relative dielectric constant of gases is %3| Determine the capacitance and maximum voltage that can be applied for this system. b. Determine maximum and minimum electric field strength if the applied voltage is U = 100 kV. а. Determine the actual electrode separation, d; effective electrode separation, a and utilization factor, ŋ for this electrode system (ɛo с. 8.854 × 10-12 F/m).

The outer radius of a concentric spherical electrode system is r, = 25 cm = constant. The system is dimensioned with regard to the optimum breakdown case. There is an insulator gas in between spheres with a breakdown strength of E, Er = 1). 25 kV/cm (the relative dielectric constant of gases is %3| Determine the capacitance and maximum voltage that can be applied for this system. b. Determine maximum and minimum electric field strength if the applied voltage is U = 100 kV. а. Determine the actual electrode separation, d; effective electrode separation, a and utilization factor, ŋ for this electrode system (ɛo с. 8.854 × 10-12 F/m).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

FF: A piece of parallel wire line has a nominal capacitance of 31.5 F/ m, and 9 H inductance per meter. Assume the radius of the conductor is 0.008 meter then find the distance between the two parallel wire lines in milimeter 8:32 PM
Estimate the dielectric losses in the solid specimen subjected to an alternating field of 40KV/cm, has an absolute permittivity of 4.445 x10-11 and the loss angle of that solid dielectric material is 0.28647at Oman power frequency. And also the same specimen while subjected to 3 KV/cm DC supply with the resistance value of 10 Mega Ohm, then determine the heat generated in the specimen.
this is an electromagnetic field and waves lesson question. Please only give the correct answer. (for example correct answer is A,B ..etx)
Q.2 Two long parallel current carrying wires are separated by 5 cm in air and are carrying current of 20A in the opposite direction. The force per meter length between the two wires will be (in N/m)
Define dielectric strength and explain how is it calculated?
A) Explain briefly various theories of breakdown in liquid dielectrics. B) What are the requirements of a sphere gap for measurement of high voltages? Discuss the advantages and disadvantages of sphere gap for measurements. C) Determine the Townsend's first ionization coefficient if a steady current of 500 µA flows through the plane electrode separated by a distance of 0.4cm when a voltage of 10 kV is applied. A current of 25 µA flows when the distance of separation is reduced to 0.1 cm and the field is kept constant at the previous value. Find also the value of y if the breakdown took place when the gap distance was changed to 0.7 cm.
1. The area of the hysteresis loop of a 1200 cm³ ferromagnetic material is 0.9 cm² with Bmax = 1.5 T. The scale factors are 1cm= 10A/m along x-axis and 1 cm = 0.8T along y-axis. Find the power loss in watts due to hysteresis if this material is subjected to an 50 Hz alternating flux density with a peak value 1.5 T.
FIGURE 5-15 A closely wound toroidal coil (Example 5-8).
Reluctance of core material (R) Cross-sectional area (A) 1520 Number of turns FUCCE Fig. 6 Magnetic coil Flux (6) Length around core (1)
Question.3(a): A piece of parallel wire line has a nominal capacitance of 0.8 F/m, and 9.5 H inductance per meter. Assume the radius of the conductor is 0.005 meter then find the distance between the two parallel wire lines in millimeters.
An oscilloscope is applied to Channel A with a frequency of 100 Hz amplitude of 3V sinusoidal sign. A sinusoidal sign with the same frequency and amplitude of 1.5 V is applied to Channel B in a phase equal to the sign in Channel A. What is the equation of the Lissajous curve that will be seen when the oscilloscope is switched to XY mode while the channels are at the same Volt/div setting?
4- The iron is of infinite permeability (u>00). For: Ri = 5.8 cm, Ro = 7.0 cm, depth3D4 cm, g 0.35 cm Calculate: a. the mean core length l and the core cross-sectional area Aç. b. the reluctance of the core Rc and that of the gap Rg. Ro R N turns