The capacitance of a multi-layer parallel plate electrode system is 4.25 picofarad Sum of the voltages across the dielectric layers is equal to the voltage applied to the entire system. The relative permittivity (&:) and electric field strength (Es) across any dielectric layer are given in table. The maximum voltage that could have been applied to the system without having any discharge is 200 kV. Find the area of electrode surface in cm? Ca = 8.85x10- F-m Layer No. Relative permittivity Electric field strength (kV/cm) 4.8 120 50 5.2 130 2.6 70 2.4 60 5.2 130 1.6 40 8. 3.2 80

The capacitance of a multi-layer parallel plate electrode system is 4.25 picofarad Sum of the voltages across the dielectric layers is equal to the voltage applied to the entire system. The relative permittivity (&:) and electric field strength (Es) across any dielectric layer are given in table. The maximum voltage that could have been applied to the system without having any discharge is 200 kV. Find the area of electrode surface in cm? Ca = 8.85x10- F-m Layer No. Relative permittivity Electric field strength (kV/cm) 4.8 120 50 5.2 130 2.6 70 2.4 60 5.2 130 1.6 40 8. 3.2 80

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Differentiate the following in a single line?
Complete the table below using the attached circuit. Note: -When computing in half wave rectifier "J1 is ON".
Explain the factor that affects the output voltage of a power supply circuit: Zener diode as a voltage regulator
. A 12 V battery is supplied by a single-phase 60 Vrms AC supply through a 4.26 Ohm resistance and a diode. What is the firing angle of the diode ? O 14.13 degree 8.13 degree 11.53 O 25.53 degree
Q1. a) Figure Q1 is a single phase 2-level voltage source converter (VSC) with a total DC voltage V-1000V. A PWM scheme, by comparing a reference value with a 1kHz triangular waveform, is used to control the switches S₁ and S2, and output 340v at Vo. With the aid of graphs explain how pulse signals for the switches are generated, sketch the output voltage Vo, determine the duty cycle and the modulation index. Va + 2 it Va d + TS₁ V {1+5₂ = Figure Q1 A single phase VSC
QUESTION 2 Given is a voltage regulator with a nominal output voltage Vo=11V. When the load current varies between 0.1A and 5A, the output voltage varies between 10.8V and 11V. - Determine the load regulation in percent, write the answer without the unit.
Electrical Engineering _ Power Electronics Notes: pls try to answer in less than 30 min.
Q1: Write the name of this Circuit L(consta ww R, R Flux from servoamplifier LOAD
In a linear power supply, where will you connect the capacitor on order to reduce the ripple output of a rectifier circuit? O in parallel with the transformer O in series with the transformer O in parallel with the load resistor O in series with the load resistor
5. For the transformer coupled half- wave rectifier circuit shown below: detei peak secondary voltage of the transformer 4:1 120V, 60H3 R. 2.5KL
Q.4) A single-phase full-wave controlled rectifier is supplied from 220V, 50Hz. The load is R 100 and L 100mH. Find the firing angle that produced ripple factor equal to 121%. Q theo WILLE K
A single-phase, full-wave diode bridge is used to supply power to a resistive load of value R = 75 2. If the supply voltage is sinusoidal, Vs 400 sin ot, calculate the average and rms values of the load current. Calculate the ripple factor for the load current and compare this with half- wave operation. =