The open V-belt drive system shown in Figure 3 has a groove angle of 30° and is used as a speed booster. The input shaft rotates at 500 rpm and has a sheave with a pitch diameter of 7.218 in and the output shaft has a sheave with a pitch diameter of 3.609 in. The center distance between the two shafts is 15.01 in. The coefficient of friction is 0.25 and the maximum tension in the tight side of the belt is 300 lb. Determine; The maximum power transmitted by the belt if its mass is 0.04 slug/ft. [Hint: P 8 (T-T2)xv P in horse power (hp), T, and T2 in (lb). v in (ft/min)]. 33000 Belts and Chains d-d, sin 20 sin--d, 20

The open V-belt drive system shown in Figure 3 has a groove angle of 30° and is used as a speed booster. The input shaft rotates at 500 rpm and has a sheave with a pitch diameter of 7.218 in and the output shaft has a sheave with a pitch diameter of 3.609 in. The center distance between the two shafts is 15.01 in. The coefficient of friction is 0.25 and the maximum tension in the tight side of the belt is 300 lb. Determine; The maximum power transmitted by the belt if its mass is 0.04 slug/ft. [Hint: P 8 (T-T2)xv P in horse power (hp), T, and T2 in (lb). v in (ft/min)]. 33000 Belts and Chains d-d, sin 20 sin--d, 20

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The shaft shown in figure below rotating at 310 rpm carries a spur pinion E. The teeth are of the 20°, full-depth, involute form. The pinion delivers 20 hp to a gear to the left as shown. Compute the torque delivered by the shaft to the pinion E and the tangential and radial forces exerted on the shaft by the pinion. Include the weight of the pinion. A B E -12- Flywheel 1550 lb 22-in dia. V-belt sheave 120 lb 9 A 20° 6-in spur gear 20° FD 45 lb WEE Q E drives Q WrE 45 16.
A chain drive is desired to couple a gearmotor with a bucket elevator. The 40 hp. gearmotor will operate at 350 rpm and the elevator drive shaft must operate as close to 60 rpm as possible. Select an appropriate chain size, commercially available sprockets, and number of links for a chain. Also calculate the actual chain speed and the center distance.
4.) A flat belt makes contact with an 16 in. diameter pulley through half its circumference. If the coefficient of friction is 0.45 , and a torque of300ft−bsis to be transmitted, calculate the belt tensions. (please type answer not write by hend)
The electric motor shown in Fig. and delivers 50 in. Ib of torque to pulley A of a furnace blower by means of a V-belt. The effective diameters of the 36° pulleys are 5 in. The coefficient of friction is 0.30. De- termine the minimum distance a to prevent slipping of the belt if the rotation of the motor is clockwise. weighs 30 lb 8 in. 20 in.
The roughly position of the automobile jack shown in the figure is a square screw with a single blade at both ends. ABC is controlled by a bolt (right-hand threaded in A, left-handed in C). square of the bolt screw has a pitch of 2.5 mm and an average diameter of 9 mm. between the bolt and the jack limbs The coefficient of static friction is 0.15, taking into account the position and load shown, you can use the jack Find the magnitude of the torque that must be applied to raise it.
Q/The layout of a crossed leather belt drive is shown in Fig. below. The belt, transmits 7.5 kW and operates at a velocity of 13 m/s approximately. The coefficient of friction is 0.3 and the permissible tensile stress for the belt material is 1.75 N/mm2. Calculate (i) The diameters of pulleys; (ii) The length of the belt and (iii) Belt tensions on the tight and slack sides. 500 грm 1000 грm d1 d2 -1500 mm-
5. For the engine-transmission-propeller problem shown below, The engine generates a torque of 219lb-ft, and it is bolted to a frame at locations A and B. The transmission reverses the rotation direction. The transmission ratio is 1.5 (i.e. the propeller speed is -1/1.5 the engine speed, the minus sign indicates the change in direction). d. Sketch the free body diagram. Be sure to show the torques at the input and outputs to the different components. Note the change in the rotation direction between the engine and shaft. e. Solve for the reaction forces at the bolt supports of the engine, if the distance between them is 1 ft. Propeller Engine Reduction ratio 1.5 Engine is attached B
A single-strand roller chain drive connects a 50-hp engine to a lawn waste chipper/shredder, as shown below. As the engine operates at 1000 rpm, the shredding teeth should rotate at 250 rpm. The driven sprocket has 60 teeth. Determine the chain speed.
The figure shows a system with a block m1 attached to a simple square thread screw with a mean diameter of 10 mm, a pitch of 3 mm and whose coefficient of static friction on the thread is 0.35. Block m1 is attached to block m2 by a rope, each of blocks m1 and m2 have a mass of 4 kg.Block m2 is in turn attached to a 15-kg block W by another rope, which passes over a static drum where the coefficient of static friction is 0.20. Determine the required Moment M that must be applied to the screw to start lifting block W. The coefficient of static friction between the surface and blocks m1 and m2 is 0.25. Need free body diagrams
The coefficient of static friction under the block a and b are the same. If the block is in the verge of sliding, find the tension at each chord. Assume that the pulley is frictionless.Recall [from Physics]:?? = ???Where:?? - is the frictional force?? - is the normal force? -coefficient of static frictiona. Determine the tensile force (lb) on the cable 1.b. Determine the tensile force (lb) on the cable 2. Plsss show complete handwritten solution. Thanksss!!
A single trapezoidal metric thread power screw is to raise a load of 60 kN. The screw has a mean diameter of 34 mm and a pitch of 5 mm. The coefficient of thread friction and collar friction are 0.15 and 0.11, respectively. The collar mean diameter is 90 mm and the screw turns at 150 rpm. Determine the total torque required to raise the load in N-m.
Two machines are coupled by means of a clutch plate with 2 contact surfaces. The plate has an inner diameter of 125 mm and an outer diameter of 200 mm and the coefficient of friction between mating surfaces is 0.35. It is assumed that shafts of both machines are co-axial and the driving shaft is rotating at a constant speed of 240 rev/min when it is suddenly brought in contact with the driven shaft/machine initially rotating at 20 rev/min. The Moment of Inertia of the driven machine is 21 kgm2. A slippage period of 6.8 sec is observed while the driven machine is brought to the full speed of the driving shaft. Analyse the frictional power transmission and calculate: The magnitude of the torque necessary to cause the described acceleration of the driven shaft :