Answered: The op amp in the circuit given below… | bartleby

Related questions

Question

The op amp in the circuit given below has R;= 100 kN, Ro = 100 N, vs= 2 mv, and A = 100,000.
100 2
100 k2
Vs
Calculate the output voltage vo for the given op amp circuit.
The output voltage vo for the given op amp circuit is
V.

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

Solve for the voltages and currents
1. a) What is series circuit T. b) Three resistors are connected in series across a 12V battery. The first resistor has the value 12, second has a voltage drop of 4V and third has a power dissipation of 12W. Calculate the value of each resistance and circuit current
An oscillator circuit is important to many applications. A simple oscillator circuit can be built by adding a neon gas tube to an RC circuit, as shown in the figure (Figure 1). Gas is normally a good insulator, and the resistance of the gas tube is essentially infinite when the light is off. This allows the capacitor to charge. When the capacitor voltage reaches a value Von, the electric field inside the tube becomes strong enough to ionize the neon gas. Visually, the tube lights with an orange glow. Electrically, the ionization of the gas provides a very-low-resistance path through the tube. The capacitor very rapidly (we can think of it as instantaneously) discharges through the tube and the capacitor voltage drops. When the capacitor voltage has dropped to a value Voff, the electric field inside the tube becomes too weak to sustain the ionization and the neon light turns off. The capacitor then starts to charge again. The capacitor voltage oscillates between Voff, when it starts…
In the circuit element shown, the current through the 6-W resistor is approximately 30 ww 6Ω 1 - 2.0 A HINT: 1. Find the Equivalent resistance of the parallel portion of the circuit. 1/Reg = 1/R1 + 1/R2 2. Find the Voltage drop across the parallel portion by using Ohm's Law. 3. Then, find the current by = VR O Amps 2.0 Amps 0.40 Amps 0.67 Amps 1.3 Amps
R, R2 V. The circuit shown above has a 20 V battery connected to two resistors in series with R, = 80 0 and R2 = 320 Q. Select the correct current through resistor 1, I, and %3D resistor 2, 12. 1= 0.05 Amps, 2= 0.05 Amps h=0.0625 Amps, l2= 0.25 Amps 1= 0.3125 Amps, 2=0.3125 Amps 1=0.25 Amps I2=0.05 Amps 1=0.25 Amps, I2=0.0625 Amps
In the figure below, ɛ = 12 V, L = 70 mH, and R = 1.0 N. %3D 0000 1(1) Determine: a) the time constant of the circuit TL = b) the initial current through the resistor I = A c) the final current through the resistor I = A d) the current through the resistor when t = 2TL I = e) the voltages across L and R at t 2TL VL = V Vn = V
K, and a generator of voltage V. Mark as true or false the following statements concerning the stor phase of V, V, V, Vc and VR- 1. V, and VR are in phase. 2. Vị leads Ve by 90°. 3. V is at angle o relative to VR- 4. VL-Vc is in phase with V,. 5. Vc lags VR by 90°. 5 give V. = 10.76 V. V.=5.68 V.
d. An RC circuit has a resistance of 20, a capacitance of 50µF, and is connected to a battery of 5V. What| will be the capacitor's maximum charge and about how long will it take to charge it to 99% of its maximum value?
For a 6.8 µF capacitor which voltage across it as shown below, what is the current flowing into the capacitor: Voltage vs Time for a Capacitor 30 25 20 10 10 15 20 25 Time (msec) Voltage (V)
Given the equation, V =Voe-(2.6x1 )t, at what time will %3D oe the voltage drop by its original value? Select one: a. t= 2566 s b. t= 2666 s C. t= 2746 s d. t 2646 s Given the equation, V – Vne RC what size of resistor would be %3D required to drop the voltage on a 250µF capacitor to its original voltage in 2 min.? Select one: a. R= 470 k2 b. R= 450 k 2 %3D R = 460 k2 С. d. R= 440 k
a) If the current in this circuit is 3 A, what must be the value of R3? b) What is the voltage drop across the 2 ohm resistor? c) What is the voltage drop across the 3 ohm resistor. d) What is the power used in the circuit in amps?
The internal resistance of a high voltage power supply is 24 MO and the output is set so that the potential difference across the output when on open circuit is 4000 V? When a load resistor R₁ is connected across the supply the voltage across R₁ is 3000 V. What is the value of the load resistor?

SEE MORE QUESTIONS