The multicand of a multiplication operation is located at the memory adress 1190H and the multiplier is located at 1191H. Write a 8085 program using minimum number of instructions, I) First, to copy those numbers to HL register pair, II) Then, call the subroutine to make the multiplication and store the result at the memory adress 2291H. Write a function (subroutine) called MULT using minimum number of instructions, I) First, to do the multiplication of those numbers in the H and L register pair, II) Return the result to the H and L pair. Important: Your codes should be exactly correct such that they will be run in simulator without any error.

Q: mplement a function that attempts to obtain a ticket a concert. The function will run on hundreds of…

A:

Q: NAME THE INSTRUCTION ONLY that will perform the following function (i.e. ADD,MOV,SUB...etc.) NOTE:…

A: Expanding can also be

Q: Using the following data definitions: byte1 BYTE OFFh, 1, 2 byte2 BYTE 14h OFFFFh, 1, 2 word1 WORD…

A: Using the above data definition we need to write instruction which moves the lower 8 bits of word2…

Q: e instruction, Add #45,R1 does Adds 45 to the value of Rl and stores it in R1 Adds the value of 45…

A: Add #45, R1 is instruction for addition.

Q: Write the register transfer operations for the following pression. ( A=C/(B-C*2)

A: Summary: - Hence we discussed all the points.

Q: assembly code

A: Introduction Assembly programming language is basically demonstrated as a basic language or in…

Q: Consider the following C functions and assembly code Assume that long is 64 bits, int is 32 bits,…

A: Multiply and store in variable same like assembly code, then in assembly code  leaq statement give…

Q: (3) (a) Write an assembly language program with proper comment for the following : A block of data…

A: Given:

Q: 6) Write assembly language code that takes an 8-bit signed number in a register as its input and…

A: Here is the detailed explanation of the solution

Q: 2. What will be the value in the destination register after each of the following instructions…

A: The correct answer for the above mentioned question is given in the following steps for your…

Q: In the instruction cycle, the operation during time T1 is: O A. AR PC O B. IR -M[AR], PC PC + 1 O c.…

A: initially, the program counter PC is loaded with the address of the first instruction in the…

Q: in Ql: Write the code based on the logic instruction for the following program emu8086 expression: A…

A: Introduction: Note Answering in python as no language mentioned Input : Given the value of A, B, C…

Q: A subtraction instruction takes two operands, subtracts the first from the second, and the result…

A: Instruction is a command which contains two parts OPCODE and OPERAND. where OPCODE is the machine…

Q: Find the pyhsical destination adress of last instruction below. MOV BX,0AAH MOV AX,1BBH MOV DS,AX…

A: MOV BX,0AAH will move data AA into register B MOV AX,1BBH will move data 1BB into register A…

Q: In a normal swap a temporary variable is needed, eg "r2 = r0; r0 = r1; r1 = r2; " swaps r0 and r1.…

A: We need to write a program to swap two registers using eor instructions.

Q: Q2. Design a control logic to implement the following register transfer statements assuming that…

A: Please check the step 2 for solution.

Q: 2. Suppose Mask = 0x00000F0F and P = 0xDCBADCBA. What is the result of the following bitwise…

A: "Since you have asked multiple question, we will solve the second one for you. If you want any…

Q: //Special operations   Show assembly instruction(s) that will preserve the significand of a number…

A: As you have posted multiple questions, we will solve the first question for you. xmm15 is a 64 bit…

Q: ust use simple assembly code to do the uestion. 6) Write assembly language code that takes an 8-bit…

A:

Q: W rite a MIPS program to continuously generate the following series of integers: 1, 2, 3, 6, 9, 18,…

A: In this MIPS program, we will generate a series of integers, beginning with 1 and doubling the…

Q: Write the sequence of micro-operations for each cycles required to execute the instruction JB R1,…

A: Task : Implement subtraction using two's complement method.

Q: What is the MIPS machine language code for the following instruction? Write opcode, rs, rt, rd,…

A: We need to find contents for the given MIPS code.

Q: 3. Write an instruction to swap the high order and low order 4 bits of AL.

A: Below I have provided a  program for the given question.

Q: Which segment will be accessed for the instruction MOV [BX],AH.

A: AX – This is the accumulator. It is of 16 bits and is again divided into two sub-8-bit registers AH…

Q: construct the program for our imaginary computer!   There must be made of at least 5 instructions…

A: Assembly language which refers to the  a low-level programming language that are used for a computer…

Q: Translate the following pseudo code to MIPS code: A-B C Consider that the variables A, B, and C…

A: (1)C codeA = B + CMIPS Codelw $t1, 0($s4)           #$t1 = Blw $t2, 0($s5)           #$t2 = Cadd…

Q: You need to write in hexadecimal (E.g: O×00114A63) for the following RISC-V assembly instruction:

A: RISC V assembly is a set of instructions and integers as well as some memory instructions. It is…

Q: CCode V Consider the following Convolutional code encoder, where the initial value of all memory…

A: The correct answer is:

Q: Consider the following instruction: AND ( %1111_0000, AL ); After its execution, what will be true…

A:

Q: What is the MIPS machine language code for the following instruction? Write opcode, rs, rt, rd,…

A:

Q: 1- Write an assembly language program to store the even contents of 8 memory locations start at…

A: According to the guidelines, we can answer only 1st question. Please upload your question one by…

Q: Write an instruction to sum of the values 9AH, 29H and F4H.Put the sum in registers R0 (low byte)…

A:

Q: For the memory locations in the table below, write MIPS code to add all the ele- ments, placing the…

A: Introduction MIPS (Microprocessor without Interlocked Pipeline Stages) is a reduced instruction set…

Q: Question 6 For the MIPS assembly instruction below, what is the corresponding C statement? Assume…

A: The MIPS assembly instructions perform the following operations: Multiply the value of register $s0…

Q: Write a function in MIPS Assembly Language that computes the next state of a linear feedback shift…

A: Given: We have to write a function in MIPS Assembly Language that computes the next state of a…

Q: a. Use the Vertical Microarchitecture Instructions set (provided in the handout) and write a…

A: here's the approach to realize the user-level instruction E:=c-(A*2)-1; GO TO 30 using the…

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer.