You need to write in hexadecimal (E.g: OX00114A63) for the following RISC-V assemblyinstruction:sub ra,gp,t1* WARNING: You MUST write the Ox followed by the 8 hexadecimal digits all in UPPERcase. If needed, add extra zeroes to have the 8 digits (this is auto graded, so no spaces,underscores or lower case). In the previous hexadecimal example Ox00114a63 is incorrect,OX114A63 is also incorrect, and 00114A63 is also incorrect. Only OX00114A63 is correct.

RISC V assembly is a set of instructions and integers as well as some memory instructions. It is…

Answered: You need to write in hexadecimal (E.g:…

Engineering

Computer Science

You need to write in hexadecimal (E.g: O×00114A63) for the following RISC-V assembly instruction:

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Related questions

Q: determine the time taken to execute the instruction if the clock frequency of 8085 is 10MHz. Mvi…

A: In 1977, Intel designed an 8- bit microprocessor by using NM technology, which is called 8085…

Q: Consider a RISC-V assembly function func1. func1 has three passing arguments stored in registers a0,…

A: In RISC-V assembly programming, understanding the structure and size of stack frames is crucial for…

Q: Question// calculate physical addressing mode for the following instruction MOVv AX,[BX].ALPHA if…

A: In the above instruction S=0200H, ALPHA=AB54H, and [BX]=900H are given. The data segment register…

Q: 1- LEA DI, (BX+50H] Suppose BX=1E3H, DI=3034H and [BX+50]=58H. The DI content after executing the…

A: Correct answer of above question is Option A- 0233H Detailed step by step explanation for correct…

Q: What is the hex representation of the given RISC-V instruction? jal x5, loop assume loop is at…

A: Solution

Q: Write the x86 assembler instruction to perform the following: for (i = x; i > 0; --i) { if (y == 1)…

A: Answer: I have done code and also I have attached code as well as code screenshot.

Q: If an instruction is not accepted and it writes to VA page 30, what will happen? A TLB that is…

A: Given: Instructions that write to VA page 30The Translation Lookaside Buffer (TLB) table is searched…

Q: According to the format specified in Unit 2, write down the RTL steps for the STO instruction of LMC…

Q: Using ONLY the add, sub and slli instruction to convert the following C statements to the…

A: This RISC-V assembly code is designed to implement a set of arithmetic operations, mirroring the…

Q: The instruction -> Add LOCA,R0 does

A: 1) Here is how this assembly level instruction is executed First the instruction is fetched from…

Q: Please write corresponding MIPS assembly instruction to the right of MIPS machine instruction.

A: We have to Write the MIPS machine Instruction for the given assembly code. The assembly codes are…

Q: For the instruction 00002480h: beq $s0, $s1, BACKTHERE compute the value of the immediate included…

A: Given -For the instruction 00002480h: beq $s0, $s1, BACKTHERE compute the value of the immediate…

Q: What is the machine code of LEGv8 instruction EOR X6,X7,X8 in hexadecimal? You are required to first…

A: Answer: Machine code: Machine code may be a worm written in machine language. It uses the…

Q: The sequence of microoperations needed to perform the failowing operation AC-M(AR] ic Select ane A.…

A: Load to AC: This instruction transfers the memory word specified by the effective address to AC. The…

Q: a) Programmable Read-Only Memory (PROM) is a computer memory chip which is programmable once it is…

A: As per bartleby guidelines if multiple questions are posted in single image, only first question…

Q: Register r10 contains the address 0x100. Write ONE ARM instruction that stores the content of r7…

A: Solution:-

Q: using RISCV(RVS) Write an instruction that multiplies the unsigned integer in x18 by 512 (in…

A: RISC-V is the type of the instruction set, which is pronounced as the risk five. This RISC-V is an…

Q: for (i=0; i<=w; i++) for (j=0; j<y; j+=2) A[3*i + j] = 2*i +3*j;

A: X4=w, X5=y, X6=i, X7=j add X6, X0, X0 // i=0 Loop1: beg X6, X4, DONE // go to DONE if i=w…

Q: Eight consecutive bytes in memory contain the hex values 00, 00, 00, 00, 00, 00, 10, 00. An FLD…

A: Given: The hex values are: 00, 00, 00, 00, 00, 00, 10, 00 After that, a FLD m64fp instruction is…

Q: What distinguishes the MUL instruction's multiplication output from the single-operand IMUL…

A: The solution for the above given question is given below:

Q: Write an assembly code to rotate a stepper motor with three main terminals in counter clockwise dual…

A: ANSWER: Assembly Code: The low level computing construct is one of the low level programming…

Q: Write the assembly instruction to create the constant:

A: The instruction to create the constant 7232118090669728530 can be assembled as follows: - ADD R1,…

Q: Find the pyhsical destination adress of last instruction below. MOV BX,0AAH MOV AX,1BBH MOV DS,AX…

A: MOV BX,0AAH will move data AA into register B MOV AX,1BBH will move data 1BB into register A…

Q: Please write a shift and add sub routine in assembly language for the MSP430. Calculate Y = mX + c…

A: Here number of ways to solve any question so we take simple step to get the desired output.…

Q: Write an instruction that loads a duplicate of ST(0) onto the FPU stack

A: FLD instruction: The FLD (load floating-point value) instruction is used to copy a floating point…

Q: There are four condtioinal flags in embedded systems, C which is carry, Z which is zero, V WHICH…

A: 1. The result of the operation would be 0x100000000, but the top bit is lost because it does not fit…

Q: Write a RISC-V instruction to :verify the following condition x3 <= x4

A: ld x5, 0(x11) slli x5, x5, 16

Q: For the following C statement, write the corresponding RISC-V assembly code. Assume that the C…

A: f is placed in the register x5 g is placed in the register x6 h is placed in the register x7 addi…

Q: Justify whether it is possible to design an expanding opcorle to allow the following to be encoded…

A: Dear Student, 1) For 15 instructions we need an opcode of 2^4 ie 4 bits and each address is of 4…

Q: The following figure shows a RISC-V Assembly code a long with the contents of the data memory (i.e.…

A: 1) answer is given below:

Q: For the MIPS instruction bne $s6,$t2,-31406, show the immediate number, opcode, rs, and rt in binary…

A: Solution:

Q: Does the CMPS instruction provide any areas of ambiguity?

A: The "CMPS" guidance (another way to say "think about strings") is a x86 low level computing…

Q: Write the x86 assembler instruction to perform the following: for(i=x; i>0; --i) { if (y ==…

A: The program given is:- for(i=x; i>0; --i) { if (y == 1) c= a+2; else…

Q: Registers in RISC-V are 64-bit. For the sake of simplicity, consider the following instructions…

A: RISC-V which is an open standard instruction set architecture that are based on established RISC…

Q: write a mips program that coverts 8-bit HEX input into mips instruction

A: write a mips program that coverts 8-bit HEX input into mips instruction

Q: only in RISC-V (RVS) answer the following both question, thumps up if both Write an instruction that…

A: We need to write instructions in Risc v for mentioned functions.

Q: Consider the MIPS I format instruction. This format is divided into 4 fields as shown here. A B C D…

A: 1) All MIPS instructions are encoded in binary.and are 32 bits long. 2) All instructions have an…

Q: LMC Instruction Set Opcode Mnemonic Definition 1xx ADD Add 2xx SUB Subtract 3xx STO Store 5xx LDA…

A: 1XX - ADD 2XX - SUBTRACT 3XX - STORE 5XX - LOAD 6XX - BRANCH 7XX - BRANCH IF 0 8XX - BRANCH IF + 901…

Q: Write an assembly language program to control two stepper motors (M1 and M2) with 9° of stepping…

A: Given:

Q: The code is in RISC V For this part write the binary code/machine level code of the following…

A: Here, I have to provide a solution to the above question.

Q: Write the LC3 assembly instruction that will branch to LOOP when the result of the following…

A: The BR instruction with condition flags is used in LC-3 assembly to obtain the instruction to branch…

Concept explainers

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer. 

Question

You need to write in hexadecimal (E.g: OX00114A63) for the following RISC-V assembly
instruction:
sub ra,gp,t1
* WARNING: You MUST write the Ox followed by the 8 hexadecimal digits all in UPPER
case. If needed, add extra zeroes to have the 8 digits (this is auto graded, so no spaces,
underscores or lower case). In the previous hexadecimal example Ox00114a63 is incorrect,
OX114A63 is also incorrect, and 00114A63 is also incorrect. Only OX00114A63 is correct.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

In CPU design, draw the datapath for the sw instruction. Include ONLY the portions necessary to carry out the operations of this instruction.
DIsassemble the following MIPS 32-bit hexadecimal instruction written as addr:instr 60005000 : Oc000020
Change this MIPS code to RISC-V Assembly using store and load. Please add comments. Allow running in RARS.
Please explain your answer in detail. Thank you
Let W be the hexadecimal pattern 0XFF8E0E13. You must detail how you get the answers, or you will receive 0 point. (a (b) (c) assembly instruction? If not, why? What decimal number does W represent if it is a two’s complement integer? What decimal number does W represent if it is an IEEE 754 floating-point number? Is it possible for W to be a RISC-V instruction? If yes, what is the corresponding 4.
What is the hex representation of the given RISC-V instruction? Note: just translate the beq instruction beq x7, x7, loop inst ... 1 inst ... inst ... 3 inst ... 4 inst ... 5 2 loop: assume loop is 6 instructions away from beq. beq x19, x10, offset = 16 bytes 13-bit immediate, imm[12:0], with value 16 Op00000010000 imm[0] discarded, always zero imm[12] 0 000000 01010 | 10011 imm[11] |1000 0 1100011 BEQ imm[4:1] 000 imm[10:5] rs2=10 rs1=19 BRANCH
hex 0x1104fff1 : bin 061000100000100111111111111001 The MIPS instruction is encoded like above. what is this doing?
If the align code is Ox9 and the 0-to-255 value is OXE6, then the literal value in hexadecimal without any leading zeros will be Ox f the iteral value is Cas000A, then the align code in decimal vill be and the D-to-255 value in decimal will be Encode the following ARM assembly instruction to ARM machine language code. ORRS r4,r5,r6, ASR #6 Ox Decode the following ARM machine language code to ARM assembly instruction. Ox02721000
Translate the following C code into RISC v (32-bit) assembly instructions, then convert to machine codes (hex format). Assume that the variable a, b. and e are stored in al, a2, and a3, respectively. Use register al for all intermediate values. C code: a-b+e - 64;
Show the assembly instruction for the following machine code, given in hexadecimal. Explain all fields in detail. 03A2F023
show your solution please
If an instruction is not accepted and it writes to VA page 30, what will happen? A TLB that is handled by software would perform better than a TLB that is controlled by hardware in the following situations: