The motor causes the aluminum shaft containing gears D, E, and F to rotate. The solid shaft has a diameter of 24 mm and a modulus of rigidity of 24 GPa. The bearings at G suddenly jams, after which gear B rotates an additional 0.27 radians and gear C rotates an additional 0.21 radians. Determine the resulting torsion, T, that must be occurring in the shaft between gears D and E. Assume that D and E are rotating the same direction. Also note that gears B and C both have a 60 mmtradius. Express your answer in Nm to the nearest whole Nm. 100 mm 30 mm 60 mm 40 mm D. 02m 08 m 0.4 m 02 m

The motor causes the aluminum shaft containing gears D, E, and F to rotate. The solid shaft has a diameter of 24 mm and a modulus of rigidity of 24 GPa. The bearings at G suddenly jams, after which gear B rotates an additional 0.27 radians and gear C rotates an additional 0.21 radians. Determine the resulting torsion, T, that must be occurring in the shaft between gears D and E. Assume that D and E are rotating the same direction. Also note that gears B and C both have a 60 mmtradius. Express your answer in Nm to the nearest whole Nm. 100 mm 30 mm 60 mm 40 mm D. 02m 08 m 0.4 m 02 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 25-kg uniform thin hollow square plate is pinned at point O, and its side L = 0.6 m. If it is subjected to the constant moment M = 83 N•m and is released from rest from the position as shown, determine the total work done to it when it has rotated O 45. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper SI unit. Take g 9.81 m/s². M 1/2 Your Answer: Answer units
Determine the elongation of a long cylindrical shaft suspended vertically from its end. Express your answer in terms of the cylinder's mass density p, stiffness E, length L, cross sectional area A, and acceleration due to gravity g. δ =
The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration kG=0.4 m. The spring’s unstretched length is L0=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is θ=30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is θ=0°. The spring’s length at the state 2 is L2=4 m. (9) The mass moment of inertial about the IC center is IIC =_________(kg·m2 ) (two decimal places)
Read the question carefully and give me right solution according to the question. Note: If you are 100 % confident then you can solve it otherwise leave it for someone. Thank you
A steel ring was shrunk into the outside of a hollow steel disc. The interference radius of the assembly is 40 mm whilst its outer and inner radii are 250 mm and 20 mm, respectively. If the angular speed at which the ring-disc assembly becomes loose is 401.8 rad/sec, determine the shrink-fit pressure at the mating surface of the assembly? Assume that Poisson's ratio for steel is 0.3 and its density is 7860 kg/m³.
The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration KG=0.4 m. The spring's unstretched length is Lo=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is 8-30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is 8-0°. The spring's length at the state 2 is L2=4 m. (5) The stretched spring length of the spring at the state 2 is_ places) HULK ܪܐ TG नेता State 2 State 1 _(m) (two decimal
- once answered correctly will UPVOTE!!
The lever AB shown in the figure is attached to the horizontal axis BC that passes through the bearing and is welded onto the fixed bearing at C. The constant of torsion of the spring of the axis BC is K; that is, a couple of magnitude K is required to rotate r radián to end B of the shaft. If the shaft is known not to be twisted when the lever AB is horizontal, determine the value of θ corresponding to the position of equilibrium if P = 150N, l= 325 mm and K = 13,5 Nm/rad. Solve by potential energy methodology and determine the stability of the equilibrium position.
Determine the magnitudes of all pin reactions for the frame loaded as shown. 850 N 280 mm OC 610 mm 300 630 A D Answers: A !! 542.95 В 3 1074.01 D = 1074.01 N
3. Two blocks, each of mass m, are attached to the ends of a massless rod which pivots as shown in Fig. 8-43. Initially the rod is held in the horizontal position and then released. Calculate the magnitude and direction of the net torque on this system when it is first released m ·l₂ m
The 13.5-lblb disk rests on the 5-lblb plate. A cord is wrapped around the periphery of the disk and attached to the wall at BB. A torque MM = 40 lb⋅ftlb⋅ft is applied to the disk. Assume the disk does not slip on the plate and the plate rests on the surface at DD having a coefficient of kinetic friction of μk = 0.2. Neglect the mass of the cord Determine the angular acceleration of the disk measured counterclockwise . Determine the time needed for the end CC of the plate to travel 3 ftft and strike the wall.