Two blocks A and B have a weight of 50 N and 30 N, respectively. They are resting on the incline for which the coemicients of static frction are =0.15 and An = 0.25. The spring has a stiffness of k 35 N/m (EQure 1) Part A Determine the inciline angle @ tor which both blocks begin to silde. Express your answer in degrees to three significant figures. ? Submit Reguest Answer Part B Find the required stretch or compression in the connecting spring tor this to occur. Express your answer to three significant figures and include the appropriate units. HẢ Value mm Figure < 1 of 1 Resuest Anawer Submit Provida Fendhack

Two blocks A and B have a weight of 50 N and 30 N, respectively. They are resting on the incline for which the coemicients of static frction are =0.15 and An = 0.25. The spring has a stiffness of k 35 N/m (EQure 1) Part A Determine the inciline angle @ tor which both blocks begin to silde. Express your answer in degrees to three significant figures. ? Submit Reguest Answer Part B Find the required stretch or compression in the connecting spring tor this to occur. Express your answer to three significant figures and include the appropriate units. HẢ Value mm Figure < 1 of 1 Resuest Anawer Submit Provida Fendhack

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please asap
Asap
DRAW THE FREE BODY DIAGRAM OF THE FOLLOWING PROBLEMS PROBLEMS 3.1 Block A has a mass of 160 kg and is supported by the flexible cables B and C. Draw the free body diagram of A. 0.5m Prob.3.1 +48 1450N 0.5m 1.Om A 30° 2.5m 780 N Prob.3.2 Prob.3.3 3.2 The vertical bar A has a mass of 100 kg. Draw the free body diagram of A assuming that all surfaces of contact are smooth. 3.3 The 30-kg bar A is supported by a smooth pin at one end and by a flexible cable at the other end. Draw the free body diagram of the bar.
Determine the tension in the cable and the horizontal and vertical components of reaction of the pin A. The pulley at D is frictionless and the cylinder weighs 83 lb.( Egure 1) Figure 38 101 Part A Determine the tension in the cable. Express your answer to three significant figures and include the appropriate units. Submit Part B Value Request Answer Determine the horizontal and vertical components of reaction of the pin A. Assume that the positive and yaxes are directed to the sight and upward, respectively A.. A₁- Submit Express your answers using three significant figures separated by a comma. Assume that the positive and y axes are directed to the right and upward, respectively VAXI vec Units Request Answer ? lb
The 10 kg block is supported by two springs having the stiffness shown. Determine the stretch of spring AB, S(AB): 0.4 m - 0.3 m 0.4 m kac - 1.5 kN/m - 1.2 KN/m Select one: O a. none of these Ob. S(AB) = 0.058 m O c. S(AB) = 0.22 m O d. S(AB) = 0.58 m
Determine Reaction and Internal Member Forces
Please asap
Determine the Grashof condition of the following mechanism as shown L. 0.1 my 0.2 m -0.2 m 60°
The gear forces shown act in planes parallel to the yz plane. The force on 20 in gear A is 300 lbf. Consider the bearings at O and B to be simple supports. For a static analysis and a factor of safety of 3.5, use both the DET and 16 in the MSST to determine the minimum safe diameter of the shaft. 10 in Consider the material to have a yield strength of 60 ksi. Gear A Solution: 24-in D. Gear C 10-in D. 20°
In the system shown, when a compression load P is applied to the rod, what is the bearing stress value in the bearings through which the d diameter pin passes? P = 10kN, pim çapı: d=20mm, bir yatağın kalınlığı: t = 10mm
STATICS OF RIGID BODIES RATE WILL BE GIVEN! NO LONG EXPLANATION NEEDED! SHOW THE COMPLETE SOLUTIONS. ANSWER IN 4 DECIMAL PLACES.
The specifications for a coil spring are known. Infinite fatigue life is required, using a safety factor of 1.3 applied to the maximum load only. The fatigue strength can be represented by a line between τmax= 600, τmin= 0 and τmax= τmin= 900 MPa.Assume both end plates are in contact with nearly a full turn of wireand that the end plate loads coincide with the spring axis.Determine a suitable combination of d, D, and N, if C = 8