the mid span. shown in Fig. i need clear ans by hand and solve very very fast in 20 min and thank you DYBALA : A Simply Supported beam of 5 m span and carries a point load of 40 kN at The beam section is in the form of hollow square bar with circular bore as Draw the shear stress distribution at 1.5 m from the left support. Fig. O 150 C Beam Cross-Section (all dimensions in mm)

the mid span. shown in Fig. i need clear ans by hand and solve very very fast in 20 min and thank you DYBALA : A Simply Supported beam of 5 m span and carries a point load of 40 kN at The beam section is in the form of hollow square bar with circular bore as Draw the shear stress distribution at 1.5 m from the left support. Fig. O 150 C Beam Cross-Section (all dimensions in mm)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please show your solution on a paper with FBD.
Kindly show complete solution. Solve the reactions and draw the shear and bending moment diagrams for the beam shown using the method of Consistent Deformations.
1. THE MEMBERS OF THE STRUCTURE SHOWN BELOW WEIGH 2918 N/M, DETERMINE THE SMALLEST DIAMETER OF PIN THAT CAN BE USED AT A IF THE SHEARING STRESS IS LIMITED TO 34470 kfa. ASSUME SINGLE SHEAR. 1.20 m 1.80m 1,20 M 0.90 m
Question 5 Match the answers in the columns. v Maximum Shear stress of a cross section. A. using an l-section instead of a rectangular section. v Maximum Bending stress of a cross section. B. Tension and bending force. C. 1m form the supports - v If a simply supported beam is subjected to a distributed load, where are you most likely to find tension bending cracks. D. At Midspan - v Ifa simply supported beam is subjected to a distributed load, where are you most likely to find shear cracks. E. Midspan at the bottom v The bending stress in a section can be reduced by using a F. Midspan at the top v Shear stress can be increased by the width of a section. G. At the supports. v The shear force in fasteners. H. Reducing the width of a section. v Moment couple on a section. 1. using a rectangular section instead of an l-section J. Shear flow K. Increasing the width of a section. L. Only at the section sides touching the NA M. In between the NA and the top/bottom fibres N. Usually at the NA…
I need the correct answer and as soon as possible please
A joint in a wooden structure shown has an applied loadF = 50 kN along the axis of the slanted member with anangle of 30°. Determine the bearing stress developedalong the plane ABC.Answer: σb ___________________
For the section shown, if the distance from the N.A to the steel centroid is 350 mm, 1944.4 x 10^6 mm^4, Es = 200 GPa, Ec = 20 GPa and M = -50 kN.m, then the strain in steel is b P -185.3 MPa O -926 x 10^-6 O 926 x 10^-6 O 185.3 MPa O zero O
show step by step solution
W A L Test beam Strain gauge (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. Section A-A Strain gauge 1 b Strain gauge 3 Strain gauge 2 B (b) Location of Huggenberger strain gauges a Referring to the above figure, calculate the location of the centroid, the second moments and product of area for the cross-section if; • D = 67 mm B = 41 mm t = 2.41 mm. From these, calculate the position and orientation of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis). Also calculate the directions of the principal second moments of area. Next, graph as scale diagram of the cross-section and plot the neutral axis on that diagram in the correct location and indicate the direction of deflection for the same conditions
Please answer me as soon as possible, it is urgent my deadline is coming, thanks a lot 4. Explain the 4 methods in classifying piling systems.
The beam shown in Fig1.carries a concentrated load of W and a total distributed load of 8 W. Determine the maximum safe value W that will not exceed allowable stresses in tension of 60 MPa, in compression of 90 MPa, or in shear of 15 MPa. 1m W ᎦᎳ ? 15 2m 1m 20mm Fig.1 140mm 20mm 2 20mm 140mm
17