The member, shown in the figure, is under tensile load of P=15 kN. The member has uniform thickness of t=5 mm. The fillet radius is r=10 mm. A hole with a diameter of di=30 mm is drilled in the middle of the member. Determine the points that have the maximum stress.

The member, shown in the figure, is under tensile load of P=15 kN. The member has uniform thickness of t=5 mm. The fillet radius is r=10 mm. A hole with a diameter of di=30 mm is drilled in the middle of the member. Determine the points that have the maximum stress.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Related questions

Q: Q2) For the problem shown in the figure, - Find the axial displacement at the end B - Determine the…

A: for solution refer below images.

Q: Q // The mechanism shown in the figure below has 0.02 in. gap at 80 Fahrenheit degree, find (a) the…

A: Given Data : δ = 0.02 in LB = 16 in…

Q: 4. The three steel (E= 29 x 10 psi) eye-bars, each 4 in. by 1.0 in in cross section, are assembled…

Q: The box beam shown in Figure P8.63b has dimensions of b=80mm, d=120mm, and t=8mm. A downward…

Q: In the figure below, a pulley can pull a 1-ton load from rest to 3 m/s upwards at 2 seconds. AB and…

A: Given: The load, W = 1 ton The speed, v = 3 m/s The time, t = 2 s The compressive stress, σ = 140…

Q: F1. The rigid bar ABC in the figure is supported by a clevis and pin at its right hand side and by…

A: Draw the free-body diagram of the beam.

Q: B L A tube is loaded eccentrically as shown in figure. The tube has 89 mm outer diameter and 7 mm…

A: Given, Outer diameter of tube = do = 89 mm = 0.089 m Thickness of tube = t = 7 mm = 0.007 m Inner…

Q: A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kNm show in…

A: Given:P=400 kNσ=120 MPainside diameter= 100 mm

Q: A rod is composed of copper and steel section rigidly bolted in the wall as shown in the figure. If…

Q: The structure of hook is made such that it is in round shape with diameter d= 20mm as shown in the…

Q: From the figure shown, the tube has an outer diameter of 80 mm and an inner diameter of 70 mm. The…

Q: 1. In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa.…

A: Solution of Question 2

Q: A circular tube AB is fixed at one end and free at the other end. The tubeis subjected to axialforce…

A: In this question, we determine the maximum normal stress Maximum normal stress, σ=PA here, P is…

Q: Determine the maximum axial force P that can be applied to the bar in the figure below. The bar is…

Q: The figure below are 3 solid cylindrical bars joined together by a flange. Find the axial stress of…

A: we will use a top to bottom approach in solving this problem

Q: The assembly shown in Figure consists of an aluminum tube AB having a cross-sectional area of 400…

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square…

Q: The figure shows a special spanner used to tighten screwed components. A torque is applied at the…

Q: The figure below shows the cross section of a steel rectangular tube, of uniform thickness t= 25 mm,…

Q: Q1 The machine element shown in the figure below is fixed supported at point B and has an applied…

Q: Figure Problem In the figure shown, determine the stress in the cable C if its area is 600 mm?.…

Q: Using direct stiffness method determine the nodal displacement of stepped bar as shown in the…

Q: 3. The weight of 20 kN homogeneous bar and load P = 50 kN are suspended from the rods A and B as…

A: Given: The weight of bar, W = 20 kN The load, P = 50 kN The cross-section of rod A, AA = 706.86 mm^2…

Q: Q3. Two bars of rectangular cross section (thickness t=15 mm) are connected by a bolt in the manner…

A: Given : P = 31 KN thickness, t of the base = 15mm Allowable shear stress in bolt ζAllow = 90 MPa…

Q: The two wooden boards shown in Figure are connected by a 0.5-in.-diameter bolt. Washers are…

Q: For the assembly shown in Figure.(5). If the stress in the steel rod become (170) Mpa when the…

Q: The coupling as shown in figure is made from steel has rectangular cross section is designed to…

Q: 2.44 The figure shows the cross section of a circular steel tube that is filled with concrete and…

A: GivenP=200kipEst=29×106 psiEco=3.5×106 psi

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

Q: Referring to the structural members of truss in the figure, determine the internal axial stress of…

Q: A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the…

Q: Q4\ A filleted. plate of thickness t supports an axial load P (Figure below). Determine the diameter…

Q: Home Work: Determine the largest load P that can be supported by the circular steel bracket shown in…

Q: A steel column of hollow circular with length, L is shown in Figure 2. The column cross section has…

Q: Q2: The pin-connected structure shown in Figure consists of a rigid bar ABCD and two axial members.…

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square…

Q: A simple pin-connected truss is loaded and supported as shown in the figure. All members of the…

A: Given Data:-Outside Diameter=5.00 inThickness=0.274 inload, P=8 kips;Q=8 kips=a=4 ft, b=8 ft &…

Q: A steel column of hollow circular cross section shown in Figure is supported on a circular steel…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

A: Please refer to the detailed solution given below, Answers- Minimum diameter required for each rod…

Q: The pins at B and D in the figure apply an axial load to diagonal bracing member BD. If BD has a…

Q: 2. A short cantilevered round peg is 60 mm in diameter and extends 10 mm from the wall. It is loaded…

A: Given data, Diameter of the peg, d = 0.06 m Extended length, L = 0.01 m Applied load, F = 40 kN =…

Q: In the figure, two planks are fastened together with a sheet plate with a thickness of 4 mm. Since 1…

Q: An axial load P is supported by the short steel column shown in the figure. The column has a…

A: Given:A=14,300 mm2σs=73 MPaσb=9 MPab=435 MPa

Q: The yoke and rod connection assembly shown in the figure below is subjected to a tensile force of 5…

Q: The two wooden boards shown in Figure are connected by a 0.5-in.-diameter bolt. Washers are…

Q: The column shown in Figure B-1(a), not drawn to scale, carries a horizontal load W applied in the…

A: Answer: The maximum allowable value of W is 25.202 kN.

Q: Question #4 Bar (1) in the figure has a cross-sectional area of 0.75 in². If the normal stress in…

Question

The member, shown in the figure, is under tensile load of P=15 kN.
The member has uniform thickness of t=5 mm. The fillet radius is
r=10 mm. A hole with a diameter of dn=30 mm is drilled in the
middle of the member. Determine the points that have the
80 mm
60 mm
maximum stress.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
While drilling a hole with a brace and bit, you exert a downward force P = 25 lb on the handle of the brace (see figure). The diameter of the crank arm is d = 7/16 in. and it s lateral offset is b = 4-7/8 in. Determine the maximum tensile and compressive stresses e1, and e2respectively, in the crank.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
A specimen used in a coupon test is shown in the figure. The stresses on element A are known to be sy= -1500 psi. Use Mohr’s circle to: (a) Find the stresses acting on the element oriented at an angle ?? = -35°. (b) Find maximum normal and shear stresses and show them on sketches of properly oriented elements.
A tension member constructed of an L inch angle section (see Table F-4(a) in Appendix F) is subjected to a tensile load P = 12.5 kips that acts through the point where the mid-lines of the legs intersect (see figure part a). Determine the maximum tensile stresser, in the angle section. Recompute the maximum tensile stress if two angles are used and P is applied as shown in the figure part b.
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at mid-span is known to be ??x= 1.5 ksi. Determine the element stresses lilt is rotated through angle ? = 450• Show these stresses on a sketch of an element oriented at that angle.