The maximum shear force at a section is 78 kN. An ISWB of height 380 mm, breadth 200 mm, thickness of web is 8 mm, with a section modulus of 897 cm3 is used as a beam at the section. The shearing stress is (in N/mm2)

The maximum shear force at a section is 78 kN. An ISWB of height 380 mm, breadth 200 mm, thickness of web is 8 mm, with a section modulus of 897 cm3 is used as a beam at the section. The shearing stress is (in N/mm2)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the maximum load based on shear design at critical section and at 1.5m from the support of…

A: the critical section for shear stress is if the support reaction introduced compression in end…

Q: A laminated plastic beam of square cross section is built up by gluing together three strips, each…

Q: determine the largest allowable spacing of rivets that join (a) the angle bars and the top plate;…

A: The Working stress of shear and bearing is given as 100 and 250 MPA yu

Q: A reinforced concrete beam has a width of 425mm and an effective depth of 900mm. The longitudinal…

A: The given data is shown below: Width=425 mmEffective depth=900 mmCompresion…

Q: The cast iron inverted T-section supports two concentrated loads of magnitude P as shown. Determine…

Q: A tripod is shown in the figure consists of three members AB, AC and AD whose lower ends are in the…

Q: A steel channel is used as a purlin of a truss. The top chord of the truss is inclined at a slope of…

A: Weight of the purlin = 79 N/mDead load, DL = 720 N/m2Live load, LL = 1000 N/m2Wind load, WL = 1440…

Q: Q.No.3: Determine the ACI design moment capacity =60000 psi. Also draw the strain diagram? 4 #9 bars…

Q: A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: A 500 Ib/ft uniform load w is applied to 6 ft rigid horizontal bar CA, pin supported at Cin single…

Q: B. Show that the strut is in compression. Knowing that the allowable shear stress for bolt at C is…

Q: H.WOLA tvaingular beam B00mm wide by 30omm height is Pinned at A, SuPPorted by acable cD and Carries…

A: As per bartleby guidelines, only 1st question among multiple questions posted need to be solved.…

Q: Bar diameters ar positioning in the figure given are representations. Refer to the proE ds statement…

Q: Two steel plates (A572, Fy = 50 ksi) are welded together to form an inverted T-beam. Determine the…

Q: n, solve the absolute maximum shear stress.

A: CALCULATIONS OF ABSOLUTE MAXIMUM SHEAR STRESS###

Q: A steel section has the following properties: A = 0.012 m^2 rt = 0.053m tf = 0.016m Sx =…

Q: Question The span of cantilever beam is 2 m. The cross-section of the beam is a hollow square with…

A: A cantilever beam- span of the beam-L=2 m=2000 mm,sides of square=100 mm,Moment of inertia I=4×105…

Q: the rectangular beam having a dimension of b= 320mm, h=460mm with 4pcs-28mm diameter reinforcing…

Q: Nominal moment capacity of the overhanging portion of the section. b. Depth of the compression…

A: Solution: Givendata flange width = 750 mm thickness of flange = 50mm Effective depth = 750 mm width…

Q: 4-43 The center post B of the assembly has an original length of 124.7 mm, whereas posts A and C…

A: The normal stress at A(&C) and B is 189.315 MPa and 21.3675 MPa, respectively.Explanation:From…

Q: Two steel plates are welded together to form an inverted T-beam and are loaded as shown below.…

A: We know that Bending stress is given by σ = MI*y For Maximum bending stress we can write σmax =…

Q: The reinforcement steel consists of 5 bars with each having a diameter of 13.75 mm. Take pb=0.425.…

A: diameter= 13.75 mmpb=0.425ymc =1.5yms =1.15NOTE:Since you have posted multiple questions, we will…

Q: Safe Support Spacing and S-1-bd Table below shows formulas for shear, bending moment and deflection…

A: Bending stress Equation , Shear stress Equation ,

Q: A beam cast monolithically with the slab thickness of 110 has a span of 4 m spaced at 6 m center to…

A: The values given in the question are as follows: Depth of slab or depth of flange(df)=110 mm Span of…

Q: In reinforced beam having a width of 300 mm and an effective depth of 600 mm, carries a moment of 80…

A: This question is related to Design concrete structure. There is Option (A) 200 mm is correct answer.

Q: A beam has a flange width of 810mm and a slab thickness of 50mm. The width of the web section is…

Q: P6-5. Sketch the bending stress distribution over each cross section. (a) M P6-5 (b)

A: Two members cross section are shown in the above figure. We have to draw bending stress distribution…

Q: 4. A 10 m span simply supported beam carries a uniform load. The beam has an adequate lateral…

Q: The average normal stresses developed in section a a of the turnbuckle, and the bolts shanks at B…

A: To find maximum value of load P

Q: Determine the minimum height h of the following beam if the maximum flexural stress is 20 MPa.

Q: 4-5 The A-36 steel rod is subjected to the loading shown. If the cross-sectional area of the rod is…

A: Displacement of b, δb =2.31 mmDisplacement of a, δa = 2.64 mmExplanation:

Q: A CONCRETE BEAM LOADED WITH A CROSS SECTION AS SHOWN EMAZO 5FT 1600 D 4 MB=0 ≤F=0 EMAO 1600(S)-RB…

A: Concrete beam with loading is given. We need to calculate shear moment diagram, maximum flexural…

Q: Q3) The beam system has a pin support at A, roller supports at D and F, an internal hinges at C.…

A: In beam AC, VA and VC = 5N In beam CF, VD and VF= 5N Σ MF = 0 -5 × 20 + VD × 15 + 100 = 0VD = 0VF…

Q: AW250 x 32.7 structural steel [E = 200 GPa] wideflange shape is loaded and supported as shown. A…

Q: A bridge girder AB on a simple span of length L = 30 m supports a distributed load of maximum…

Q: The absolute value of the maximum shear stress in a rectangular section (b x h) due to an internal…

A: Given : Rectangular section dimensions Shear force To find: Maximum shear stress

Q: reaction at B, and D? What is the shear and bending moment at distance @2m from B on the span BD?…

Q: A 290 kg/m light crane rail sits on and is securely fastened to a W400mmx67kg/m crane girder.The…

A: Solution:- Given data:- Vertical load (V) = 80 kNHorizontal load (H) =8 kNA = 8580 mm2d = 400 mmbf =…

Q: A three-span continuous beam has an internal hinge at B. Section B is at the mid-span of AC. Section…

Q: An I-section girder has a web 600 mm x 12,5 mm and flanges 300 mm x 25 mm. The girder must withstand…

Q: The W12×40 section in Fig. below is used as a simply supported beam. Two point loads applied at the…

A: The beam is a W12x40 sectionThe modulus of elasticity of the material is 10,000 ksiThe point load is…

Q: T section of a beam is fabricated from 2 - 12 mm x 150 mm steel plates and joined by welding as…

A: To determine The maximum compressive stress. The maximum tensile stress. The maximum shear stress.…

Question

The maximum shear force at a section is 78 kN. An ISWB of height
380 mm, breadth 200 mm, thickness of web is 8 mm, with a section
modulus of 897 cm3 is used as a beam at the section. The shearing
stress is (in N/mm2)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

statics of rigid bodies
Calculate the maximum moment (with diagram) & maximum shear (with diagram)
A structural member is fabricated with the cross section show below and is eccentrically loaded with F. - 26--| F 2t F b. Use G = 77.2 GPa. If I = 4 m, t= 3 mm, b = 80 mm, and F = 121 kN, Determine the maximum shear stress due to torsion. Select the correct response: 168.056 MPa 215.278 MPa 155.556 MPa of 133.333 MPa 22
Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear and have a diameter of 0.250 in. Assume L= 4.0 ft. If the average shear stress in the bolts cannot exceed 70 ksi, determine the maximum distributed load wmax that can be supported by the structure. (1) A Answer: Wmax IN L B kips/ft
Forces are applied at points A and B of the solid cast-iron bracket shown. Knowing that the bracket has a diameter of 0.8 in., determine the principal stresses and the maxi- mum shearing stress at (a) point H, (b) point K. 1 in. H. K 2500 lb В 3.5 in. 2.5 in. A 600 lb