The magnitude of the resultant force acting on the bracket is to be 400 N. Determine the magnitude of F, if o - 30°. F- 650 N 45° F- 500 N

Q: Q1// The force F - 50 lb acts on the gear tooth. Resolve this force into two components acting along…

A:

Q: 10 N 10 N 20 N E M 10N B 6.0m 4.0m L 8 BAYS @ 3.0 m EACH 20 N - The force at member IK is equal to O…

A:

Q: Determine F=20N at all points. the moment of the force

A: TO FIND MOMENT AT ALL POINTS

Q: Qg. find The pressure at Point A ? b00 B い

A:

Q: Assume that P- 35 kips and L- 5 ft. Determine the reaction force at C. Assume that El is constant…

A: Applying three moment equation to span (1) and span…

Q: tart A cable is used as a laundry washing line whose end points are fixed at A and B. The clothes on…

A: Given that the endpoints of the cable used as a laundry washing line are fixed at A and B.  constant…

Q: If F=80 N, determine the magnitude and coordinate diretion angles of the couple moment. The pipe…

A: Given dataF=80 NFINDdetermine the magnitude and coordinate diretion angles of the couple moment

Q: ipe. use mohr's circle

A:

Q: 1. At the instant 0 Determine the angular velocity of the connecting rod BC & velocity of slider C…

A:

Q: De Ex 2m

A:

Q: (Two body system) Find the reactions of the supports and the presse in the hinge gived. 早 3 bata…

A:

Q: Q4-A) Gate AB is 1.2 m long and 0.8 m into the paper. Compute the force F on the gate and its center…

A: Compute the force F on the gate and its center of pressure,X

Q: 100 kN Find the horizontal base reactions for the portal frame shown, when the vertical bars have A…

A:

Q: Determine the x, y, z components of internal loading at a section passing through point B in the…

A: Given: The force vector is, Consider the figure,

Q: Calculate the vertical displacement at the internal hinge.

A: Given : Calculate the vertical displacement at the internal hinge.

Q: 1-5. The shaft is supported by a smooth thrust bearing at B and a smooth journal bearing at A.…

A:

Q: Determine the force on each element of the roof truss shown in the figure. Indicate whether each…

A: Consider the figure, Here, T is the tension and C is the compression.

Q: 250 mm A press is used to apply a compressive vertical force, F, to cylinder E. The lower jaw (below…

A: We have to calculating Fρ if a)∅=45°                                           b) ∅=80°

Q: Construct the influence diagrams for the reactions at A, B, and C, and the shear and moment at a…

A:

Q: F11-5. Determine the angle where the 50-kg bar is in equilibrium. The spring is unstretched at 0=…

A:

Q: ots Date No. •CONSIDER THE SIMPLY -SUPPORTED DVER HANG BEAM SHOWN. THERE IS A PIN SUPPORT AT A. A…

A: Given beam is simply supported with overhang at end.The length of span,  =10mThe magnitude of…

Q: 5-6 The solid 1.25-in.-diameter shaft is used to transmit the torques applied to the gears. If it is…

A: Shear stressExplanation:Step 1:Step 2: Step 3: Step 4:

Q: Find the force in spring if support A rotate 0.003 rad C.W and C settle 10mm E=200GPA and…

A:

Q: Handle forces F₁-(41-45-10k) N and F,- (21 are applied to the electric drill(Eigure 1) Replace this…

A:

Q: Problem 2: Replace the three forces which act on the bent bar by a force-couple system at the…

A: In this problem, we are given three forces acting on a bent bar. We must replace these forces with a…

Q: Derive a formula for the total elongation (6) of the bar due to the load P За За

A:

Q: F 650 N F = 500 N

A:

Q: 1m 1.5m 1m 25KN 2m B 0.8m C 1.8m D E

A: Find force in AB, AC and BC

Q: 300 lb 30° 224 lb 361 lb

A:

Q: 7. The force F on the piston in Figure 5 causes the link AB to exert a force P = 2 kN on the pin B…

A: T

Q: H.W.18/ The plane rectangular gate can pivot about the support at B. For the conditions given, is it…

A: It will be Stable if the centre of pressure (P) of the water above it will lie at point B otherwise…

Q: tho The 200-kg engine block is suspended by the cables AB and AC. The angle a = 40°. The FBD…

A:

Q: P (kN) Şekildeki kafes sistemde çubuk kuvvetlerini Basınç-çekme hesaplayınız. durumlarını A B…

A:

Q: Determine the axial force in member DA KN.0

A:

Q: PRAW THE SHEAR AND moment PIAGRAM. 10/4/10kwon loku Tim उफ +3m t उफ 3m

A: (NOTE - According to Bartleby guidelines, we are directed to solve only one question at one time.…

Q: Analyze the frame and draw S.D and B.M? 10 kN/m B 5 m El constant 10 m

A:

Q: Replace the forces acting on the plate by a wrench. Specify the force and couple moment for the…

A: Consider the figure,

Q: pin The solid 24-mm-diameter steel [E = 220 GPa] shaft supports two belt pulleys. Assume that the…

A: Given:- P=530 NQ=610 NLAB=250 mmLBC=180 mmLCD=250 mmLDE=180 mmE=220 GPaDiameter of solid shaft = 24…

Q: Determine the equivalent resultant force and couple moment at point A for the given force system.…

A:

Q: Q3/ The three forces and the couple are applied to the bracket shown in Figure below. Determine (1)…

A:

Q: 1.3 ft 200 Ib

A:

Q: Determine the minimum downward force to keep the block from slipping. The block weighs W kN. The…

A:

Laws of Equilibrium

A body is said to be in equilibrium if the system of forces acting on the body tends to keep the body at rest, in other words, there is no translation motion or net torque on the body. Under such conditions, the equilibrium conditions are to be applied to analyze the condition. The branch of mechanics that deals with this condition is known as 'statics'. Under equilibrium, there are no net forces on the body.