*8-52. Beam AB has a negligible mass and thickness, and supports the 200-kg uniform block. It is pinned at A and rests on the top of a post, having a mass of 20 kg and negligible thickness. Determine the two coefficients of static friction at B and at C so that when the magnitude of the applied force is increased to P = 300 N, the post slips at both B and C simultaneously. -1.5 m -1.5 m- 1m + 0.75 m B C

*8-52. Beam AB has a negligible mass and thickness, and supports the 200-kg uniform block. It is pinned at A and rests on the top of a post, having a mass of 20 kg and negligible thickness. Determine the two coefficients of static friction at B and at C so that when the magnitude of the applied force is increased to P = 300 N, the post slips at both B and C simultaneously. -1.5 m -1.5 m- 1m + 0.75 m B C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Force of member BH and indicate if it is in tension or compression.
26.0
Q2. Member ABC is supported by two fixed supports at points A and C. The member has heights of 100mm at points A and C whereas the height is 600mm at point B. A point torque of 10KN.m is applied Im away from the point A. Determine the reactions at supports A and C. Write vour results in the box below. Use G-100GPA. B A T= 10 kN.m 100 mm 600 mm 1 m 1 m 2 m
The solid 36 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 500 N, Q = 800 N, LAB = 600 mm, LBC = 850 mm, LCD = 850 mm.
1. A frame held taut by a rope connected at D and E, is pin connected at B. If 1500 N is perpendicular to the member AB, determine the tension on the rope and the horizontal and vertical components of forces at B. Assume roller connection at A. 2000 N 2 m Fim--1 m- 1500 N 2 m 2 m 45° A
A)determine determinacy and stability b) identify the zero force members
The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. Determine (a) the maximum shear stress in the shaft; and (b) the angle of twist of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible. A 4 in. 3.5 in. 3.5 in. ID В C te-4 ft- | 2 ft - 6 ft-
*4-88. If the allowable normal stress for the bar is = 120 MPa, determine the maximum axial force P that can be applied to the bar. σ O allow PA 40 mm 5 mm 20 mm r = 10 mm 20 mm Probs. 4-87/88 P
Determine the force in each member of the pin-connected truss. AE is constant. Use force method
The compound beam is pin supported at C and supported by a roller at A and B. Note that there is a hinge at D. Find the reactions at the supports. Neglecting the thickness of the beam. (Provide the whole solution along with its FBD)
The solid 25 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 700 N, Q = 950 N, LAB = 600 mm, LBC = 1050 mm, LCD = 1050 mm.
Determine all REACTION components in all of the supports for the beam shown using the following method and then Draw the Shear and Moment Diagram. a.) Force Method b.) Castigliano's Theorem of Least Work 30 kips 20 kips -6' -6'- -6'- A D B E -12' -12- CONSTANT EI