The lower ends of the three bars in the figure are the same level before the rigid homogeneous W=100 kN block is attached. The properties of the bars are shown in the table. The temperature of the bars is then increased by 80°C. The block is assumed to remain horizontal after all deformations have occured. a.) Which of the following most nearly gives the temperature rise to cause all of the applied loads to be supported by the steel rods? b.) Which of the following most nearly gives the stress developed in the bronze bar? c.) Which of the following most nearly gives the stress developed in the steel bar? Length, L Area, A Modulus elasticity, E Coefficient of 11.7x10C linear Steel 1.00 m 500 m2 of 200 GPa Bronze 1.60 m 900 m 83 GPa Bronze Steel Steel 18x104 C expansion, a

The lower ends of the three bars in the figure are the same level before the rigid homogeneous W=100 kN block is attached. The properties of the bars are shown in the table. The temperature of the bars is then increased by 80°C. The block is assumed to remain horizontal after all deformations have occured. a.) Which of the following most nearly gives the temperature rise to cause all of the applied loads to be supported by the steel rods? b.) Which of the following most nearly gives the stress developed in the bronze bar? c.) Which of the following most nearly gives the stress developed in the steel bar? Length, L Area, A Modulus elasticity, E Coefficient of 11.7x10C linear Steel 1.00 m 500 m2 of 200 GPa Bronze 1.60 m 900 m 83 GPa Bronze Steel Steel 18x104 C expansion, a

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need this asap. Thank you!
PROBLEM, 2 a) In the concrete-beam show in the figure given below indicate (by drawing) the main reinforcement steel-bars, assembly steel-bars and the stir-ups. concrete beam P2 b) Write down the conditions for an object to be in stable (static, equilibrium) position.
А P 200 mm В E 150 mm F Three steel (E=200 GPa) rods (AB, CD and EF) support a load of P=30 kN as shown in the figure. Each of the rods AB and CD has a 80-mm2 cross-sectional area and rod EF has a 120-mm2 cross-sectional area. (a) Write the equilibrium equation for the rigid member BED in vertical direction, (b) write the compatibility equation for the given bar system, (c) determine the force in rod EF (d) determine the average normal stress in rod EF.
i need clear ans and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛
5- The solid rod is subjected to the loading snown. Determine the state of stress at point A, and show the results on a differential volume element located at this point. (HINT: For 100 KN load, the bending will happen about a vertical axis passing through the centroid.) 100 KN 10 KN 200 mm 20 AN 30 mm
subject: statics of rigid bodiesshow your solution please
The 20-kg drum is suspended from the hook mounted on the wooden frame. Determine the state of stress at point E on the cross section of the frame atsection a–a. Indicate the results on an element.
The brass rod AB is fixed connected at A. When the temperature is T₁-50 °C, there is a 3 mm gap between its end (point B) and the wall C. The cross-sectional area of the rod is 10 cm². Ignore the weight of the bar. The temperature is now increased to T₂-130 °C and the rod AB is pushing against the wall at C. Ebr = 100 GPa, abr = 20 x 10-6/°C Fallow 70 MPa L = 3m A 3 m B/C с 3 mm a. Draw a FBD for when the temperature is increased to T₂ and write down the force balance for this scenario. Call the reactions at FA and FC. Ton =1) und prit brolim volgen Aistis Intelesa si s b. State the compatibility condition and solve for the reactions at A and C.
H.W.1: A rigid steel bar ABC is pinned at B and supported by two rods at A and C. There is no strain in the rods before load P is applied. After load P is applied, the axial strain in rod (1) is +910 pe. Determine the axial strain in rod (2). (1) C 2,000 mm 520 mm ad Na 400 mm 1,250 mm A (2)
Hand written please.
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
Two rigid beams are connected by two elastic bars. The first beam is fixed at point A, while the second is simply supported at point B. Bar 2 is heated by a temperature AT. Compute the forces in the two bars. EA EA, ar