The load in the circuit shown absorbs 50 kVA of complex power at power factar pf = 0.83 lagging when the load voltage is Vi. = 480/0 Vrms. 0.150 j025 ww SL pf Part C Find the pawer factor of the saurce. Enter your answer as pf, +1. where the pf is expressed so t significant figures and +1 is entered to indicate whether the pf is lesading (+1) or lagging (-1). > Vlew Avallable Hintis)

The load in the circuit shown absorbs 50 kVA of complex power at power factar pf = 0.83 lagging when the load voltage is Vi. = 480/0 Vrms. 0.150 j025 ww SL pf Part C Find the pawer factor of the saurce. Enter your answer as pf, +1. where the pf is expressed so t significant figures and +1 is entered to indicate whether the pf is lesading (+1) or lagging (-1). > Vlew Avallable Hintis)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Repeat the design using TFF by making the state diagram of the circuit given below.
A capacitor of capacity C₁ is charged upto V volt and then connected in parallel to an uncharged capacitor of capacity C₂. The final potential difference across each will be (a) (c) C₂V G₁ + C₂ (1+2) GV G + C₂ (4) (1-²) v (b)
Question Distinguish between combinational and sequential circuits
A. 9
For R1=9000, R2=2000, R3=6000, R4=5000, C1=0.006, C2=D0.002 & 11=0.007 A in the shown circuit, obtain the energy stored in each capacitor under dc conditions. C2 R4 ŽR3 ER2 ŽRI C1= Energy stored in C1= Energy stored in C2=
Answer the following and choose the correct answer below.
Electrical Engineering Please solve Rout. Op-Amp #1 ID: Name: Yc R5 Rc Rc 05 res Q3 RB5 RB3 04 R6 v1- v2 Q1 Q2 Ce R4 R1 06 VE6 RBC Vo R08 Ro9 Q7 09 R7 R2 R3 -Vee
) Discuss the difference between the R2 and the adjusted R2.
Please asap
FDA in hexadecimal equal to . .in octal O a. 12x1+22x10+75x100 O b. 12x1+32x10+74x100 O c. 12x1+12x10+76x100 O d. 2x1+13x10+76x100
Original Schematic and OrCAD Schematic: The input primary voltage is 250V, frequency 50 Hz, primary inductance setting is 2000H and secondary inductance is 10H and voltage peak to peak ripple is approximately equal to 92mv. U1 D4 IN our DINA002 C3 DIN002 90u R1 R2 10k TXI BC540A V1 VOFF =0 VAMPL 2 FREQ- 50 AC0 XFRM_LINICT-SEC D5 DIN4002 C2 0.384m 84 5 HH
6674 in octal equal to . .in hexadecimal O a. 1C x1+ 1A x10 +C x100 O b. 2C x1+ 19 x10 +C x100 O c. Dx1+ B x10 +C x100 O d. C x1+ 1BX10 +C x100