3. In the AC circuit shown in the Figure the AC voltage is given by E 20VZ-35° in the phasor form. The AC frequency is 60 Hz (a) Find the Impedance seen by the AC power source. (b) Find the current flowing through the circuit in the form /,(t) Asin(t+). + 0°). (c) Find the voltage across the capacitor. Report it in the form v(t) Asin(at = (d) Find the voltage across the inductor. Report it in the phasor form. VL Ve Report box: + HH (a)Ziot Ω X102 R =2Q 0 sin( (b)s , A t+ 20VZ-35 ( (c)Vc sin( ), V 0 V 2 (d)VL

Q: Find the Vout for the circuit shown below. R1 R2 10kohm 2kohm U1 R3 15V 4kohm OPAMP 3T_VIRTUAL R4…

A:

Q: The input and output points or junctions in a signal-flow graph are called . backwared pates nodes O…

A: Correct option is  Node A node is defined as the point of intersection of the branches.

Q: 14. Compute the minimal value of K so that the steady-state error due to a unit step distur- bance…

A:

Q: A sequential circuit containing one JK-flipflop and one T-flipflop is shown in the figure below. Th…

A: Given logic diagram is shown below. The expression we get from the above logic diagram is z=xy2+y1…

Q: Given the circuit in figure below, find the z parameter. 1. Is 32

A:

Q: Choose the 8088 signals that are used to generate IORD.[You may use the schematic] A) RD B) WR C)…

A: IORD input output Read pin is connected to RD.

Q: An RTD has R=D159 Q at -80C, what is the sensor resistor at 86 °C, let a = 1 x 10-4°C.

A:

Q: Find the control ratio C/R for the system given below H₂ G₂ G₁ H₂ G₂

A:

Q: Answer quickly please.

A: multiplexer comprises: Four data input lines named D0, D1, D2, and D3. Two select lines: S0 and S1.…

Q: nadural frealvency fallowing -damfed damping order and ratio af Second 28 2+14+78

A:

Q: In the following circuit, derive next-state functions for the signals Y1,Y2. Draw a state diagram…

A: Let us write down the next state for various input and present state combination. It is clear from…

Q: - For the circuit, kalculate the current i 82 ww 32 30 V 22 ww ww- 4 A 10

A:

Q: Could you explain how these factors cause the degradation?

A: Explaining  how the given factors causes the degradation: 1-Moisture and Oxygen:  We know Perovskite…

Q: and . . are. . :8 considered exponential .functions in MATLAB

A: Diag is inbuilt function used in MATLAB to create a diagonal matrix All the elements other than…

Q: it the olen toof tranffer fynction the 5tem is of G(5) H(S): then closed - Loof will be Locubed -15…

A:

Q: For part C, can you put the expression in sum-of-product form please. Not clear

A:

Q: V- Design an ADC circuit using OPAMP

A: In analog to digital converter, OPAMP is usually employed for the following requirements, they form…

Q: (d/m c/m Seopped by TonSecopne

A: Analog circuit for the dynamics of a Spring Mass System.

Q: Electrical Engineering Find the value of R2 and R4 after executing the following instructions: LDR…

A: The given information is written below.LDR R1, =0XFF00FF00LDR R0, =LIST1LDR R2, [R0]BIC R4, R2,…

Q: SHOW, THE CIRCUIT DLAGRAMS BELOW CAL CULATE: (A. ). RT (B) It (c)Pr IT A. 150V 132 D ww to (20) Lo 中

A: Given circuit shown

Q: R1 R2 v(t) (+ vc (t) i(t) iz(t) (a) ne matrix equation is defined by b1,(s) d a e %D 1,(s) C 000

A:

Q: Do you think it is also possible to perform k-map using maxterms? How? Explain the differences when…

A:

Q: 1 Q2- Using convolution property to find time function of- 6+5ja-w?

A:

Q: A charging RC circuit has a switched-control DC voltage source of 6V and has a series RC of 20 ohms…

A: In this question dc source with transient given....We have to find out time constant , capacitor and…

Q: Design the circuit with the state diagram below with one-hot coding.

A:

Q: V₁₂ C R₁ M R3 Vin1 R₂ > RH - Vo [find the formula for Vo] in terms of Vinz, Vin1, R₁, R₂, R3, Ra…

A: In this question, we need to determine the output voltage in term of given known parameters. We…

Q: Create five Kirchhoff's Current Law (KCL) problem with figure and solve it(Show complete solution)

A:

Q: The convolution of rect function of width w with itself produces: Select one: a. tri function with…

A: According to question: Let the two rectangular pulses x(t) and h(t) be given as…

Q: Schematic diagram: IC diagram: +5V GND

A: please find the solution in  below image

Q: 2) Sketch the signals x[n] = u[n + 3] – u[n] + 0.5"u[n] – 0.5"-4u[n – 4] and y[n] = nu[-n] – S n -…

A: The signals are expressed in terms of the unit step signal, u[n], and unit impulse function, δ[n].

Q: FDA in hexadecimal equal to . .in octal O a. 12x1+32x10+74x100 O b. 12x1+12x10+76x100 O c.…

A:

Q: By Nodal Analysis, determine the voltage V₂ of the circuit V. 252 jsn V

A:

Q: Given the system in figure Realize using state space. 0.5 -1.16 2-1 rl(n) Z-1 r2(n) -1.25

A:

Gradient of a Scalar Field

Consider a room or a place where the temperature is denoted by a scalar field T, such that at each point (x, y, z), the temperature is given as T(x, y, z). It is independent of time, in which the temperature rises most quickly. The gradient of T will show the direction at that point by moving away from (x, y, z). How far will the rise in temperature in that direction be determined by the gradient magnitude? Consider a surface that has a height above sea level at point (x, y) which is given by H(x, y). At that point, pointing in the direction of the steepest slope or grade is the gradient of H. The magnitude of the gradient of the vector gives the steepness of the slope at that point. How a scalar field changes in another direction can be measured by the gradient by taking a dot product rather than just the direction of the greatest change?