The link shown, made of AISI C1045 steel, as rolled, is subjected to a tensile load of 8000 Ib. Let h = 1.5 b. If the load is repeated but not reversed, determine the dimensions of the section with the design based on (a) ultimate strength, (b) yield strength. (c) If this link, which is 15 in. long., must not elongate more than 0.005 in., what should be the dimensions of the cross section? For AISI C1045 steel, as rolled Su = 96 ksi, Sy = 59, ksi E = 30x10^6 PSI, Nu = factor of safety = 6 (for repeated but not reversed load) Ny = factor of safety = 3 (for repeated but not reversed load)

The link shown, made of AISI C1045 steel, as rolled, is subjected to a tensile load of 8000 Ib. Let h = 1.5 b. If the load is repeated but not reversed, determine the dimensions of the section with the design based on (a) ultimate strength, (b) yield strength. (c) If this link, which is 15 in. long., must not elongate more than 0.005 in., what should be the dimensions of the cross section? For AISI C1045 steel, as rolled Su = 96 ksi, Sy = 59, ksi E = 30x10^6 PSI, Nu = factor of safety = 6 (for repeated but not reversed load) Ny = factor of safety = 3 (for repeated but not reversed load)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 12” X 16”simply supported pine wood beam is being considered to carry a uniform load distribution across a span of 12’ as shown. In addition to the uniform load, the beam is also subjected to a tensile load of 20 kips. If the ultimate tensile stress in pine wood is 4500 psi, determine whether the beam is considered safe according to the Allowable Stress Method, using a Factor of Safety 2.5. Hint: you can calculate the maximum tensile stress in the cross-section without having to use Mohr’s circle
A leafs spring contains 4 full-length and 8 graduated leafs. The eyebolts at the support are 20 inches apart and the system should carry a load of 400 lbs. If the thickness of the available bronze plate is 1“ and Sy = 80 ksi, what leaf width is required at FOS = 8?
Show work pls, answer correctly.
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 14 mm, and the rod length was 440 mm. When the applied torque reached 225.3 N-m, a shear strain of 2105 microradians was measured in the specimen. What was the angle of twist in the specimen? Calculate the shear stress in the specimen. Answer: T = MPa
Don't Copy, I need correct solution within 10-20minutes. Please do it fast. [Handwritten recommended]
I need the solution and answer for this problem. Also, please make the solution neat and readable. Thank you.
None
A ¼ inch diameter steel rod is to carry an axial load of 2000 lbs. If the yield strength is 38 ksi, will the rod yield?
A bar made of carbon-steel of size 12mm x 20mm has a yield stress of 400 MPa and ultimate tensile strength of550 MPa. Tha gauge length of the specimen tested under tension loading is 350mm. a. Determine its elongation when a tension load of 75 KN is applied. b. Determine the maximum load the bar can take before it fractures. Take Youngs Modulus of steel as 200,000 MPa
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 14 mm, and the rod length was 440 mm. When the applied torque reached 225.3 N-m, a shear strain of 2105 microradians was measured in the specimen. What was the angle of twist in the specimen? Calculate the shear stress in the specimen. Answer: T= 418.16 Use Hooke's Law to calculate the shear modulus of the specimen. answer: MPa G = i MPa
Why did it became 4F/A from F/A, in (a)
Two parts of a machine, both made from steel, are held together by 5 equally-spaced M6 x 1.0 grade 8.8 bolts that are uniformly tightened to provide a total initial clamping force of 23 kN in the members. Each bolt has a proof stress of 600 MPa, and a tensile area of 20.1 mm². The elasticities are such that the joint constant is 0.2. A uniform static tensile load of 12 kN is applied to the entire joint after it has been preloaded. What is the magnitude of the total clamping force in the joint after the application of the tensile load? Express your answer in units of kilonewtons.