The laboratory tests on a soil sample gave the following results: 1). Natural water content, W₁ = 25% 2). Liquid limit, WL = 60% 3). Plastic limit, Wp = 35% 4). Percentage of particle less than 2μ = 20% The value of activity number is

The laboratory tests on a soil sample gave the following results: 1). Natural water content, W₁ = 25% 2). Liquid limit, WL = 60% 3). Plastic limit, Wp = 35% 4). Percentage of particle less than 2μ = 20% The value of activity number is

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.12P

See similar textbooks

Related questions

Q: (4)

A: The term 'structure' alludes to whatever is developed or worked from various interrelated parts with…

Q: what is design strength. The material of the steel is SM275 and the size is 22mm. The sectional area…

A: Tensile Strength : Tensile means "competent of being drawn out or stretched." Steel's tensile…

Q: A bar spring arrangement as shown in the figure is subjected to temperature rise given by Due to…

A: temperature rise given by

Q: A Three rods of equal length L and cross section area A, made of material Aluminum, rubber, steel…

A: Three rods made of different material but having equal length L, area A and load F. We need to…

Q: find l for the impact of hardness on humans and the environment along with the bibliography

A: Impact of hardness on humans One of the most obvious effects of hard water is skin irritation and…

Concept explainers

Soil engineering for highway design

Soil engineering is a part of geotechnical engineering that deals with the characteristics of soil. It also helps to understand the behavior of the soil in different conditions. The basic concepts of soil are studied to check the strength, compressibility, and porosity of the soil. This makes soil engineering an important topic for civil engineering.

Question

Find the correct solution

The laboratory tests on a soil sample gave the following results:
1). Natural water content, W₁ = 25%
2). Liquid limit, WL = 60%
3). Plastic limit, Wp = 35%
4). Percentage of particle less than 2μ = 20%
The value of activity number is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given that:

VIEW

Step 2: Solution:

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Results from a liquid limit test conducted on a soil are given below. a. Determine the liquid limit of the soil. b. If it is known that the PI = 6.5, what would be the plastic limit of the soil? c. Determine the liquidity index of the soil if win situ = 23.8%
Refer to the soil in Problem 4.5. Using the Casagrande plasticity chart, graphically estimate the shrinkage limit of the soil as shown in Figure 4.22. 4.5 The following data were obtained by conducting liquid limit and plastic limit tests on a soil collected from the site. Liquid limit tests: Plastic limit test: PL = 19.3% a. Draw the flow curve and determine the liquid limit. b. Using the Casagrande plasticity chart (Figure 4.21), determine the soil type.
Refer to Problem 2.C.1. Results of the sieve analysis for Soils A, B, and C are given below. To obtain a more representative sample for further geotechnical testing, a ternary blend is created by uniformly mixing 8000 kg of each soil. Answer the following questions. a. If a sieve analysis is conducted on the mixture using the same set of sieves as shown above, compute the mass retained (as a percentage) and cumulative percent passing in each sieve. b. What would be the uniformity coefficient (Cu) and the coefficient of gradation (Cc) of the mixture?
The properties of seven different clayey soils are shown below (Skempton and Northey, 1952). Investigate the relationship between the strength and plasticity characteristics by performing the following tasks: a. Estimate the plasticity index for each soil using Skemptons definition of activity [Eq. (4.28)]. b. Estimate the probable mineral composition of the clay soils based on PI and A (use Table 4.3) c. Sensitivity (St) refers to the loss of strength when the soil is remolded or disturbed. It is defined as the ratio of the undisturbed strength (f-undisturbed) to the remolded strength (f-remolded)) at the same moisture content [Eq. (12.49)]. From the given data, estimate f-remolded for the clay soils. d. Plot the variations of undisturbed and remolded shear strengths with the activity, A, and explain the observed behavior.
A hydrometer test has the following result: Gs = 2.65, temperature of water = 26 C, and L = 10.4 cm at 45 minutes after the start of sedimentation (see Figure 2.25). What is the diameter D of the smallest-size particles that have settled beyond the zone of measurement at that time (that is, t = 45 min)? Figure 2.25 ASTM 152H type of hydrometer placed inside the sedimentation cylinder (Courtesy of Khaled Sobhan, Florida Atlantic University, Boca Raton, Florida)
The subsurface characteristics for a highway pavement rehabilitation project in the southeastern United States are shown in a boring log in Figure 5.13. The highway structure consists of the asphalt pavement underlain by four different soil strata up to a depth of 20 ft, after which the boring was terminated. Some data on the grain size and plasticity characteristics are also provided for each stratum. Perform the following tasks: 1. Determine the AASHTO soil classification and the group index (GI) for each layer. 2. Determine the most probable group symbols and group names for the various layers according to the Unified soil classification system. Use Table 5.3 and the soil characteristics given in the boring log.
The following data were obtained by conducting liquid limit and plastic limit tests on a soil collected from the site. Liquid limit tests: Plastic limit test: PL = 19.3% a. Draw the flow curve and determine the liquid limit. b. Using the Casagrande plasticity chart (Figure 4.21), determine the soil type.
Three groups of students from the Geotechnical Engineering class collected soil-aggregate samples for laboratory testing from a recycled aggregate processing plant in Palm Beach County, Florida. Three samples, denoted by Soil A, Soil B, and Soil C, were collected from three locations of the aggregate stockpile, and sieve analyses were conducted (see Figure 2.35). (a) (b) Figure 2.35 (a) Soil-aggregate stockpile; (b) sieve analysis (Courtesy of Khaled Sobhan, Florida Atlantic University, Boca Raton, Florida) a. Determine the coefficient of uniformity and the coefficient of gradation for Soils A, B, and C. b. Which one is coarser: Soil A or Soil C? Justify your answer. c. Although the soils are obtained from the same stockpile, why are the curves so different? (Hint: Comment on particle segregation and representative field sampling.) d. Determine the percentages of gravel, sand and fines according to Unified Soil Classification System.