The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the position shown. Member BD is 15 mm thick and is connected at Cto the vertical rod by a 9-mm-diameter bolt. Know that P= 2.8 kN and e = 75°. 100 mm- 175 mn D B 20 200 mm F 45 mm Determine the bearing stress at Cin member BD.

The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the position shown. Member BD is 15 mm thick and is connected at Cto the vertical rod by a 9-mm-diameter bolt. Know that P= 2.8 kN and e = 75°. 100 mm- 175 mn D B 20 200 mm F 45 mm Determine the bearing stress at Cin member BD.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A threaded rod and nut arrangement are guided with two washers, upper and lower washers tightened into a base plate. Considering that the base plate carries a load of 120 kNincluding its self-weight which is distributed equally: a.Determine the stress on the lower washers before the buts are tightened. b.Determine the stress int the upper washer when the nuts are tightened so as to produce a tension of 5kN on the bolt. c.Determine the stress int the lower washer when the nuts are tightened so as to produce a tension of 5kN on the bolt.
QUESTION 2 Consider that x = 2.76 ft and y = 7.01 ft. B The 5.7-in diameter steel shaft AB is attached into the rigid wall at C and supported by a smooth bearing at A. The lever AC is welded to the end of the shaft. The maximum allowable stress for shaft AB is 355 psi. Determine the maximum allowable force P in lbs. C
2. Determine the normal stress at members BD, CD and DE. Diameter of all members is 22 mm. 200 kN 200 kN 100 kN - 3 m 100 kN - 3 m 6 m - 3 m - 2 m 4 m
The short cylindrical block of aluminum, having an original diameter, do, of 0.4 in. and an original length, Lo, of 2.0 in., is placed in the smooth jaws of a vice and squeezed until the axial load applied is 900 lb. Determine: (a) the decrease in its length (b) its new diameter EAL = 10000ksi and vAL = 0.33 Lo do
A pin-connected truss is loaded and supported as shown. Determine a. The normal stress in member DE if it has a cross-sectional area of 750 mm?. b. The minimal cross-sectional area for member BC if the normal stress is limited to 30 MPa B 3 m E F D - 3 m- - 3 m - 3 m 10 kN 15 kN
The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the largest vertical load P that can be applied at C if the stress in the steel rod is limited to 35 ksi and the vertical movement of end C must not exceed 0.12 in. Neglect the weights of the members. L=4 ft A=0.5 in.2 E= 29 x 10 psi P. T-2 t 3 n ANSWER: Ib
Problem 1 (Lecture 03) Three forces act on the bracket shown to the right. Note that for this problem, the direction (0) of F1 is measured from the positive x' axis, positive clockwise. Complete the following: a) Determine the direction (0) and magnitude of F₁ so that the overall resultant force is directed along the positive x' axis and has a magnitude of 1 kN. b) Determine the unit vector u₂ (in Cartesian notation) for the direction of F2. y Ꮎ F₁ F₂ 45° 30° = 450 N F3 = 200 N X
i need typing answer only
Determine the largest axial load P that can be safely supported by a flat steel bar consisting of two portions, both 10 mm thick and, respectively, 40 and 80 mm wide, connected by fillets of radius r=4 mm. Assume an allowable normal stress of 180 MPa.
A set of 10 bolts is to be used to provide a clamping force of 50000 lb between two components of a machine. The load is shared equally among the 4 bolts. Knowing that the grade of the material is SAE Grade 4, if each is to be stressed to 90 %of its proof strength. Then the required tensile stress area is: Select one: A. A, = 0.0714 in В. B. A, = 0.22 in %3D 2. C. A, = 0.0865 in 2. D. A, = 0.0855 in
5. Three wood boards, each 3.5 in. wide, are joined by the 3/4-in.-diameter bolt. If the working stresses for wood are 750 psi in tension and 1450 psi in bearing, find the largest allowable value of the force P. ² 1 in. P 2 in. P 1 in. T in.
The aluminum rod ABC (E =10.1* 106 psi), which consists of two cylindrical portions AB and BC, is to be replaced with a cylindrical steel rod DE (E =29 * 106 psi) of the same overall length. Deter-mine the minimum required diameter d of the steel rod if its vertical deformation is not to exceed the deformation of the aluminum rod under the same load and if the allowable stress in the steel rod is not to exceed 24 ks