The hydraulic cylinder BD exerts on member ABC a force P directed along line BD. Knowing that P must have a 750-N component perpendicular to member ABC, determine (a) the magnitude of the force P, (b) its component parallel to ABC? Show the formula and exact solution

Q: The steel ring has a weight W=0.5 N and is suspended on the surface of the water (p=1,000 kg/m³,…

A: Given information:

Q: The frame supports the distributed load shown. Draw the free body diagram and find the reaction…

A: Draw FBD:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

A:

Q: The homogeneous cylinder of weight W rests in a frictionless right angles corner. Determine the…

A: Given data in question  Weight W FBD To find out  Normal reactions at A and B.

Q: The d = 13-mm-diameter solid rod passes through a D = 18-mm-diameter hole in the support plate. When…

A: Solution attached below

Q: A 12ft cantilever beam is subjected a 180 lb/ft uniform load and a vertical support of 1200 lb on…

A:

Q: Find the maximum force P (in N) that can be applied to block A without causing both blocks to move.…

A: Find the maximum force P (in N) that can be applied to block A without causing both blocks to move.

Q: e AB has a width of 1.5 m and m. Determine the horizontale ical components of reaction

A: According to given data  Plate AB has a width of 1.5 m and a radius of 3 m. To , Determine the…

Q: Problem #1 X N/m Y N/m B Am В m 1. What is the total resultant vertical load in the beam AB? (N) 2.…

A: X=429 N/m Y=29 N/m A=2m B=9m From the question, we can see that there is a combined loading…

Q: 8. If the pressure remains a constant, then a) Vr1 > Vr2 b) Vr1 < Vr2 c) Vr1 = Vr2 d) Vr1 is a zero

A:

Q: The 10.5-kg uniform rod is pinned at end A. It is also subjected to a couple moment of 50 Nm. The…

A: Stiffness, k = 60 N/ m Mass of rod = 10.5 Kg

Q: The weight of the suspended object is W = 52 lb (Figure 1)

A:

Q: 2-2: A wire of 2 mm diameter is wound round a circular shaft of 1 metre diameter. What are the…

A:

Q: Block A has a mass of 20 kg, and blocks B and C have masses of 10 kg each. Knowing that the blocks…

A:

Q: The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A is…

A: Given:- Inner diameter of pipe, di=12 inWall thickness, t=0.25 inWater pressure inside pipe, P=300…

Q: 2- Find the hydrostatic force on the quarter circle. into screen is 1,a (m). n=7ab0 (N/m') 2.b (m)…

A: Given data, γ1=7720 N/m3γ2=9872 N/m3H1=2.2 mH2=1.7 mr=1.2 mL=1.7 m

Q: The 39 kg drum is suspended from the hook mounted on the wooden frame. Determine the state of normal…

A:

Q: Show your solutions and choose the right answers

A:

Q: Show complete solution. Draw the following structures then classify whether Statically Determinate,…

A: Static indeterminacy is a conjecture that shows the difference between the total number of unknowns…

Q: Determine the vertical reaction at support B in kN-m. w = 15 kN/m L1=7m L2=4 m L1 W L2 B

A:

Q: SHOW COMPLETE SOLUTION PLS  VALUES: A= 5 B = 5 C = 1 Y = 25

A:

Q: Question 6 Using the flexibility method, determine the reactions at the supports A and D in the…

A:

Q: A. The resultant of the four belt tensions and couple C is force R acting through points O. 1. What…

A:

Q: Given an element with stresses as indicated in the figure below, use method of the Pole (only) to…

A: The given values are as follows,σx=20KPA(tension)σy=100KPacompressionτxy=35KPa

Q: The beam is subjected to a load F = 400 N and is supported by the rope and the smooth surfaces at A…

A: The given figure is shown below:

Q: Find the value and direction of the resultant of the concurrent forces shown in figure.

A: Given data F1 = 100KN makes angle with horizontal = 30ο F2 = 20KN F3 = 30KN and F4 = 10KN

Q: A building (or machine) is shaken by a periodic force f(t) defined bye -C, --st<- f(t) = 3C, st< 20…

A: According to the guidelines , we are only allowed to answer one question at a time. so I am…

Q: D (5000 mm2) (4000 mm) E (5000 mm) 3 m 4000 mm) (S000 mm?) B (5000 mm?) A 100 kN 2 panels at 4 m 8 m…

A:

Q: A steel strip of length L = 200 mm is fixed at A and rest at B on a vertical spring of stiffness k=…

A:

Q: show your solution and graph too thanks

A: The resultant is calculated by the concepts of resolution and composition.

Q: Q.3) The Figure shown a beam with all dimensions. (a) Determine the bending stress at point H. 180…

A: Data given: Asked: Bending stress at point H. If the bending stress at point k is 9 MPa (T)…

Q: -2 m- 60 KN B. 4 m 50 kN/m C

A:

Q: Problem (5): Two designs for a beam are to consider the support be considered. moment is equal to…

A: Beam formation methods are provided by IS-code. These codes are required to design any object…

Q: 2. A rope is tied to a weight at A. The rope passes over two frictionless pulleys B and E. The other…

A:

Q: Show your step-by-step solution.

A:

Q: The hydraulic cylinder is subjected to three forces. An 8-kN force is exerted on the cylinder at B…

A:

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.